- Rigid chassis
- WhichTractor size: Standard-size
- Not independently tested
- 1983–1990
WhichTractor size, not the maker’s category
Derived by WhichTractor from a sourced three-point linkage. How we decide what a machine is
Deutz-Fahr DX 6.10 Full specifications
KHD F6L 912.74 six-cylinder diesel. The manufacturer claimed 98.2 horsepower. No laboratory has tested one, so there is no measured figure at the shaft.
Engine power, claimed · gross or net not stated
98.2 hp
73.2 kW as stated by the source
Not independently tested
Claimed · standard not stated by the source
Source · Traktorenlexikon, “Deutz-Fahr DX 6.10”, claimed
- Weight
- 10,472 lb
- 3-point lift
- 11,464 lb
- Hyd. flow
- 14.7 gpm
- Top speed
- 18.6–24.9 mph
Deutz-Fahr DX 6.10 specs: key facts
The Deutz-Fahr DX 6.10 was built from 1983 to 1990.
The Deutz-Fahr DX 6.10 has a claimed engine power (gross or net not stated) of 73.2 kW (98.2 hp); it has no measured PTO figure.
The Deutz-Fahr DX 6.10 was offered in two-wheel-drive and four-wheel-drive versions.
The Deutz-Fahr DX 6.10 has a KHD F6L 912.74 engine, a 6-cylinder 5.65 L diesel unit.
The Deutz-Fahr DX 6.10 weighs 4,750 kg (10,472 lb) unladen.
The Deutz-Fahr DX 6.10 has an independent rear PTO running at 540/1000 rpm.
The three-point hitch of the Deutz-Fahr DX 6.10 lifts 5,200 kg (11,464 lb) at the lower-link ends.
The hydraulic pump of the Deutz-Fahr DX 6.10 delivers 55.6 L/min (14.7 gpm).
Source · Traktorenlexikon, “Deutz-Fahr DX 6.10”
How much horsepower does a DX 6.10 have?
The only figure for the DX 6.10 is 98.2 hp (73.2 kW) of claimed engine power, gross or net not stated, no test standard stated — not power at the shaft.
Source · Traktorenlexikon, “Deutz-Fahr DX 6.10”
What engine is in a DX 6.10?
A DX 6.10 has a KHD F6L 912.74, a 6-cylinder 5.65 L diesel engine.
| Make & model | KHD F6L 912.74 |
|---|---|
| Cylinders | 6, air-cooled |
| Displacement | 344.9 ci · 5.65 L |
| Max torque | 263 lb·ft · 356 N·m @ 1,503 rpm |
| Electrical system | 12 V |
Source · Traktorenlexikon, “Deutz-Fahr DX 6.10”
How much will a DX 6.10 lift, and what is its hydraulic flow?
A DX 6.10 lifts 11,464 lb (5,200 kg) at the lower-link ends.
| Pump flow | 14.7 gpm · 55.6 L/min |
|---|---|
| Lift at ends | 11,464 lb · 5,200 kg |
| Rear PTO | Independent, 540/1000 rpmEngages under load |
Source · Traktorenlexikon, “Deutz-Fahr DX 6.10”
What transmission does a DX 6.10 have?
Transmission specifications for the DX 6.10 are below.
| Steering | Hydrostatic DANFOSS steering type OSPC-140 OR |
|---|---|
| Top speed | 18.6–24.9 mph · 30–40 km/hthe article lists alternatives |
Source · Traktorenlexikon, “Deutz-Fahr DX 6.10”
How much does a DX 6.10 weigh?
A DX 6.10 weighs 10,472 lb (4,750 kg) unladen.
| Unladen weight | 10,472 lb · 4,750 kg |
|---|---|
| Maximum permissible mass | 14,991 lb · 6,800 kg |
| Maximum front axle load | 5,952 lb · 2,700 kg |
| Maximum rear axle load | 10,141 lb · 4,600 kg |
| Wheelbase | 106.4 in · 2,703 mm |
| Length | 179.1 in · 4,550 mm |
| Width | 90.7 in · 2,304 mm |
| Height | 111.0 in · 2,820 mm |
| Ground clearance | 20.1 in · 510 mm |
| Front track | 70.9–78.7 in · 1,800–2,000 mmthe article lists alternatives |
| Rear track | 70.9–78.7 in · 1,800–2,000 mm |
| Turning radius, braked | 15.9 ft · 4.86 m |
Source · Traktorenlexikon, “Deutz-Fahr DX 6.10”
Which tractors compare with a DX 6.10?
Within 10% of its 91.2 hp at the PTO (claimed), the same type, and first built within 15 years of it.
- SOMECA 980 (TD)91.1 hp PTO, claimed · 1979–1983Side by side with the DX 6.10 →
- Renault 110-14 TS91.5 hp PTO, claimed · 1986–1989Side by side with the DX 6.10 →
- Case-IH 5230 (DT)90.8 hp PTO, claimed · 1989–1997Side by side with the DX 6.10 →
- Fiat 1000 Super (DT)91 hp PTO, claimed · 1976–1979Side by side with the DX 6.10 →
- Fiat 1000 Super (TD)90.7 hp PTO, claimed · 1976–1979Side by side with the DX 6.10 →
- SOMECA 1000 Super (TD)90.7 hp PTO, claimed · 1976–1979Side by side with the DX 6.10 →
Everything else people ask
Is a DX 6.10 two-wheel drive or four-wheel drive?
The Deutz-Fahr DX 6.10 was offered in two-wheel-drive and four-wheel-drive versions.
What PTO does a DX 6.10 have?
A DX 6.10 has a independent 540/1000 rpm rear PTO.
Where this page comes from
Compiled from Traktorenlexikon, “Deutz-Fahr DX 6.10”.
Sources
Facts taken from these documents, units converted. Numbers beside a figure refer to this list. Licences and attribution
- Traktorenlexikon: Deutz-Fahr DX 6.10 — CC BY-SA 4.0, WIKIBOOKS-TL-73375 · revision 1054427. Wikibooks contributors (Traktorenlexikon). Original document