10 material differences · fewer than 12
Tractor oneDeutz-Fahr DX 6.101983–1990No measured PTO figureTractor twoZETOR 10111/101451984–1990No measured PTO figure
Which should you choose?
Read our verdict on the DX 6.10 and the 10111/10145 → It is generated from the rows below by a fixed, versioned rule set, and names the figure behind every call.
Field by field
10 material differences · 4 fields identical or within 5%, which is not counted as material
| Field | DX 6.10 | 10111/10145 | Gap |
|---|---|---|---|
| Engine | |||
| Engine power, claimed claimed | 98.2 hp | 98.6 hp | — |
| Engine declared | KHD F6L 912.74 | ZETOR Z-8002.1 | differs |
| Displacement declared | 5.65 L | 4.56 L | +24% DX 6.10 |
| Maximum torque declared | 263 lb·ft · 356 N·m | 227 lb·ft · 308 N·m | +16% DX 6.10 |
| Transmission | |||
| Top speed declared | 18.6–24.9 mph · 30–40 km/h | 18.6–24.9 mph · 30–40 km/h | — |
| Clutch declared | — | Pedal-operated dry ZTS single-disc clutch | — |
| Hydraulics & hitch | |||
| Pump flow declared | 14.7 gpm · 55.6 L/min | 12.2 gpm · 46.2 L/min | +20% DX 6.10 |
| Pressure declared | — | 2,828 psi · 195 bar | — |
| Rear PTO speeds declared | 540/1000 rpm | 540/1000 rpm | — |
| Weight & dimensions | |||
| Unladen weight declared | 10,472 lb · 4,750 kg | 9,414 lb · 4,270 kg | +11% DX 6.10 |
| Maximum permissible mass declared | 14,991 lb · 6,800 kg | — | — |
| Wheelbase declared | 106.4 in · 2,703 mm | 93.9 in · 2,385 mm | +13% DX 6.10 |
| Length declared | 179.1 in · 4,550 mm | 163.0 in · 4,140 mm | +10% DX 6.10 |
| Width declared | 90.7 in · 2,304 mm | 76.4–89.8 in · 1,940–2,280 mm | differs |
| Ground clearance declared | 20.1 in · 510 mm | 11.8 in · 300 mm | +70% DX 6.10 |
| Turning radius, braked declared | 15.9 ft · 4.86 m | 11.9 ft · 3.63 m | +34% DX 6.10 |
| Fuel tank declared | 126.8 qt · 120 L | 132.1 qt · 125.0 L | — |
Height is not in this table. It is not one measurement: the sources measure it to different points — over the cab on some machines, over the steering wheel or the exhaust on others — and the same tractor measured two ways can differ by most of a metre. It appears here only when both machines' figures carry the point they were measured to and it is the same point, which is not the case for these two. Each machine's own page prints its height as its source gives it.
Deutz-Fahr DX 6.10 sources
- Source: Traktorenlexikon, “Deutz-Fahr DX 6.10”
ZETOR 10111/10145 sources
- Source: Traktorenlexikon, “Zetor 10111/10145”