- Rigid chassis
- WhichTractor size: Utility
- Not independently tested
- 1984–1989
WhichTractor size, not the maker’s category
Derived by WhichTractor from a sourced three-point linkage. How we decide what a machine is
Deutz-Fahr DX 3.70 Full specifications
KHD F4L 912 four-cylinder diesel. The manufacturer claimed 69.1 horsepower. No laboratory has tested one, so there is no measured figure at the shaft.
Engine power, claimed · gross or net not stated
69.1 hp
51.5 kW as stated by the source
Not independently tested
Claimed · standard not stated by the source
Source · Traktorenlexikon, “Deutz-Fahr DX 3.70”, claimed
- Weight
- 6,923 lb
- 3-point lift
- 5,732 lb
- Top speed
- 18.6 mph
Deutz-Fahr DX 3.70 specs: key facts
The Deutz-Fahr DX 3.70 was built from 1984 to 1989.
The Deutz-Fahr DX 3.70 has a claimed engine power (gross or net not stated) of 51.5 kW (69.1 hp); it has no measured PTO figure.
The Deutz-Fahr DX 3.70 was built in two-wheel drive (2WD) and four-wheel drive (4WD) versions, depending on configuration.
The Deutz-Fahr DX 3.70 has a KHD F4L 912 engine, a 4-cylinder 3.77 L diesel unit.Source 1
The Deutz-Fahr DX 3.70 weighs 3,140 kg (6,923 lb) unladen.
The Deutz-Fahr DX 3.70 has a rear PTO running at 540/1000 rpm.
The three-point hitch of the Deutz-Fahr DX 3.70 lifts 2,600 kg (5,732 lb) at the lower-link ends.
Source · Traktorenlexikon, “Deutz-Fahr DX 3.70”
How much horsepower does a DX 3.70 have?
The only figure for the DX 3.70 is 69.1 hp (51.5 kW) of claimed engine power, gross or net not stated, no test standard stated — not power at the shaft.
Source · Traktorenlexikon, “Deutz-Fahr DX 3.70”
What engine is in a DX 3.70?
A DX 3.70 has a KHD F4L 912, a 4-cylinder 3.77 L diesel engine.
| Make & model | KHD F4L 912Source 1 |
|---|---|
| Cylinders | 4, air-cooledSource 1 |
| Displacement | 229.9 ci · 3.77 LSource 1 |
| Max torque | 173 lb·ft · 234 N·m @ 1,600 rpm |
| Injection | direct injection |
| Electrical system | 12 V |
Source · Traktorenlexikon, “Deutz-Fahr DX 3.70”
How much will a DX 3.70 lift?
A DX 3.70 lifts 5,732 lb (2,600 kg) at the lower-link ends.
| Pressure | 3,481 psi · 240 bar |
|---|---|
| Lift at ends | 5,732 lb · 2,600 kg |
| Rear PTO | 540/1000 rpm @ 2,025 engine rpm |
| PTO shaft | 1 3/8"-6 splines |
Source · Traktorenlexikon, “Deutz-Fahr DX 3.70”
What transmission does a DX 3.70 have?
Transmission specifications for the DX 3.70 are below.
| Clutch | independent dry double clutch |
|---|---|
| Brakes | pedal-operated double drum brake |
| Steering | hydrostatic Danfoss steering |
| Top speed | 18.6 mph · 30 km/h |
Source · Traktorenlexikon, “Deutz-Fahr DX 3.70”
How much does a DX 3.70 weigh?
A DX 3.70 weighs 6,923 lb (3,140 kg) unladen.
| Unladen weight | 6,923 lb · 3,140 kgtwo-wheel-drive version |
|---|---|
| Maximum permissible mass | 11,023 lb · 5,000 kg |
| Maximum front axle load | 4,630 lb · 2,100 kg |
| Maximum rear axle load | 8,818 lb · 4,000 kg |
| Wheelbase | 91.6 in · 2,327 mmtwo-wheel-drive version |
| Length | 153.9 in · 3,910 mmtwo-wheel-drive version |
| Width | 84.2 in · 2,138 mm |
| Height | 97.2 in · 2,470 mm |
| Ground clearance | 18.0 in · 457 mmtwo-wheel-drive version |
| Front track | 55.1–74.8 in · 1,400–1,900 mmtwo-wheel-drive version |
| Rear track | 59.8–65.0 in · 1,520–1,650 mmthe article lists alternatives |
Source · Traktorenlexikon, “Deutz-Fahr DX 3.70”
Which tractors compare with a DX 3.70?
Within 10% of its 59.7 hp at the PTO (claimed), the same type, and first built within 15 years of it.
- Landini R-6500 (DT)59.7 hp PTO, claimed · 1973–1983Side by side with the DX 3.70 →
- VALMET 70059.7 hp PTO, claimed · 1997–2002Side by side with the DX 3.70 →
- Renault 68-14 RS59.8 hp PTO, claimed · 1984–1987Side by side with the DX 3.70 →
- Renault 68-12 RS59.8 hp PTO, claimed · 1983–1987Side by side with the DX 3.70 →
- Landini R-7880 (DT)59.4 hp PTO, claimed · 1987–2000Side by side with the DX 3.70 →
- Renault 75-32 MX59.4 hp PTO, claimed · 1989–1993Side by side with the DX 3.70 →
Everything else people ask
Is a DX 3.70 two-wheel drive or four-wheel drive?
The Deutz-Fahr DX 3.70 was built in two-wheel drive (2WD) and four-wheel drive (4WD) versions, depending on configuration.
What PTO does a DX 3.70 have?
A DX 3.70 has a 540/1000 rpm rear PTO on a 1 3/8"-6 splines shaft.
Where this page comes from
Compiled from Traktorenlexikon, “Deutz D 6006”; and Traktorenlexikon, “Deutz-Fahr DX 3.70”.
Sources
Facts taken from these documents, units converted. Numbers beside a figure refer to this list. Licences and attribution
- Traktorenlexikon: Deutz D 6006 — CC BY-SA 4.0, WIKIBOOKS-TL-51755 · revision 1024090. Wikibooks contributors (Traktorenlexikon). Original document
- Traktorenlexikon: Deutz-Fahr DX 3.70 — CC BY-SA 4.0, WIKIBOOKS-TL-88349 · revision 990210. Wikibooks contributors (Traktorenlexikon). Original document