10 material differences · fewer than 12
Tractor oneDeutz-Fahr DX 3.701984–1989No measured PTO figureTractor twoSAME Explorer 70 (DT)1986–1990No measured PTO figure
Which should you choose?
Read our verdict on the DX 3.70 and the Explorer 70 (DT) → It is generated from the rows below by a fixed, versioned rule set, and names the figure behind every call.
Field by field
10 material differences · 4 fields identical or within 5%, which is not counted as material
| Field | DX 3.70 | Explorer 70 (DT) | Gap |
|---|---|---|---|
| Engine | |||
| Engine power, claimed claimed | 69.1 hp | 69.1 hp | — |
| Engine declared | KHD F4L 912 | SAME 1000.4 A | differs |
| Displacement declared | 3.77 L | 4.00 L | +6% Explorer 70 (DT) |
| Maximum torque declared | 173 lb·ft · 234 N·m | — | — |
| Transmission | |||
| Top speed declared | 18.6 mph · 30 km/h | 18.6–24.9 mph · 30–40 km/h | differs |
| Clutch declared | independent dry double clutch | Pedal-operated dry SAME single-disc clutch | differs |
| Hydraulics & hitch | |||
| Hydraulic control declared | — | Load sensing | — |
| Pump flow declared | — | 9.5 gpm · 36.0 L/min | — |
| Pressure declared | 3,481 psi · 240 bar | 1,740 psi · 120 bar | +100% DX 3.70 |
| Three-point lift, at the coupling points declared | 5,732 lb · 2,600 kg | 7,562 lb · 3,430 kg | +32% Explorer 70 (DT) |
| Rear PTO speeds declared | 540/1000 rpm | 540/1000 rpm | — |
| Weight & dimensions | |||
| Unladen weight declared | 6,923 lb · 3,140 kg | 6,085 lb · 2,760 kg | +14% DX 3.70 |
| Maximum permissible mass declared | 11,023 lb · 5,000 kg | — | — |
| Wheelbase declared | 91.6 in · 2,327 mm | 91.5 in · 2,325 mm | — |
| Length declared | 153.9 in · 3,910 mm | 157.1 in · 3,990 mm | — |
| Width declared | 84.2 in · 2,138 mm | 73.6–101.2 in · 1,870–2,570 mm | differs |
| Ground clearance declared | 18.0 in · 457 mm | 19.3 in · 490 mm | +7% Explorer 70 (DT) |
| Turning radius, braked declared | — | 9.4 ft · 2.88 m | — |
| Fuel tank declared | 100.4 qt · 95 L | 70.8 qt · 67.0 L | +42% DX 3.70 |
Height is not in this table. It is not one measurement: the sources measure it to different points — over the cab on some machines, over the steering wheel or the exhaust on others — and the same tractor measured two ways can differ by most of a metre. It appears here only when both machines' figures carry the point they were measured to and it is the same point, which is not the case for these two. Each machine's own page prints its height as its source gives it.
Deutz-Fahr DX 3.70 sources
- Source: Traktorenlexikon, “Deutz-Fahr DX 3.70”
- Source: Traktorenlexikon, “Deutz D 6006”
SAME Explorer 70 (DT) sources
- Source: Traktorenlexikon, “SAME Explorer 70”