- Rigid chassis
- WhichTractor size: Standard-size
- Not independently tested
- 1973–1980
It was ranked on an engine power figure whose source does not say gross or net. WhichTractor size, not the maker’s category
Derived by WhichTractor from a sourced three-point linkage. How we decide what a machine is
VALMET 1102 (-4) Full specifications
VALMET 411 BS or 411 CS four-cylinder diesel. The manufacturer claimed 100.6 horsepower. No laboratory has tested one, so there is no measured figure at the shaft.
Engine power, claimed · gross or net not stated
100.6 hp
75.0 kW as stated by the source
Not independently tested
Claimed · standard not stated by the source
Source · Traktorenlexikon, “Valmet 1102”, claimed
- Weight
- 8,598 lb
- Hyd. flow
- 9.2 gpm
- Top speed
- 18.6 mph
VALMET 1102 (-4) specs: key facts
The VALMET 1102 (-4) was built from 1973 to 1980.
The VALMET 1102 (-4) has a claimed engine power (gross or net not stated) of 75.0 kW (100.6 hp); it has no measured PTO figure.
The VALMET 1102 (-4) was built in two-wheel drive (2WD) and four-wheel drive (4WD) versions, depending on configuration.
The VALMET 1102 (-4) has a VALMET 411 BS or 411 CS engine, a 4-cylinder diesel unit.
The VALMET 1102 (-4) weighs 3,900 kg (8,598 lb) unladen.
The VALMET 1102 (-4) has a rear PTO running at 540/1000 rpm.
The hydraulic pump of the VALMET 1102 (-4) delivers 35.0 L/min (9.2 gpm).
Source · Traktorenlexikon, “Valmet 1102”
How much horsepower does an 1102 (-4) have?
The only figure for the 1102 (-4) is 100.6 hp (75.0 kW) of claimed engine power, gross or net not stated, no test standard stated — not power at the shaft.
Source · Traktorenlexikon, “Valmet 1102”
What engine is in an 1102 (-4)?
An 1102 (-4) has a VALMET 411 BS or 411 CS, a 4-cylinder diesel engine.
| Make & model | VALMET 411 BS or 411 CS |
|---|---|
| Cylinders | 4, liquid-cooled |
| Injection | direct injection |
| Electrical system | 12 V |
Source · Traktorenlexikon, “Valmet 1102”
How much will an 1102 (-4) lift, and what is its hydraulic flow?
Hydraulic and PTO specifications for the 1102 (-4) are below.
| Pump flow | 9.2 gpm · 35.0 L/min |
|---|---|
| Hitch category | Category 2 |
| Rear PTO | 540/1000 rpm @ 1,746 engine rpm |
| PTO shaft | 1 3/8"- 6 splines (Form-A) |
Source · Traktorenlexikon, “Valmet 1102”
What transmission does an 1102 (-4) have?
Transmission specifications for the 1102 (-4) are below.
| Clutch | dry Fichtel & Sachs double clutch |
|---|---|
| Brakes | Pedal-operated hydraulic Valmet double disc brakes acting on differential shafts |
| Steering | Hydrostatic Danfoss steering, type Orbitrol-Ospa 160 |
| Top speed | 18.6 mph · 30 km/h |
Source · Traktorenlexikon, “Valmet 1102”
How much does an 1102 (-4) weigh?
An 1102 (-4) weighs 8,598 lb (3,900 kg) unladen.
| Unladen weight | 8,598 lb · 3,900 kgtwo-wheel-drive version |
|---|---|
| Wheelbase | 91.3 in · 2,320 mmtwo-wheel-drive version |
| Length | 154.7 in · 3,930 mmtwo-wheel-drive version |
| Width | 78.0 in · 1,980 mmtwo-wheel-drive version |
| Height | 106.7 in · 2,710 mmtwo-wheel-drive version |
| Ground clearance | 20.5 in · 520 mmtwo-wheel-drive version |
| Front track | 58.7–66.5 in · 1,490–1,690 mmtwo-wheel-drive version |
| Rear track | 63.8–76.4 in · 1,620–1,940 mmtwo-wheel-drive version |
| Turning radius, braked | 12.1 ft · 3.70 m |
Source · Traktorenlexikon, “Valmet 1102”
Which tractors compare with an 1102 (-4)?
Within 10% of its 100.6 hp of claimed engine power, the same type, and first built within 15 years of it.
- SAME Tiger 100 (DT)101 hp engine, claimed · 1977–1980Side by side with the 1102 (-4) →
- International Harvester 105599 hp engine, claimed · 1977–1982Side by side with the 1102 (-4) →
- Fiat 1000 (DT)98.7 hp engine, claimed · 1972–1976Side by side with the 1102 (-4) →
- John Deere 402098.7 hp engine, claimed · 1965–1972Side by side with the 1102 (-4) →
- Ford 740098.6 hp engine, claimed · 1970–1975Side by side with the 1102 (-4) →
- Massey Ferguson MF 2640102.6 hp engine, claimed · 1980–1985Side by side with the 1102 (-4) →
Everything else people ask
Is an 1102 (-4) two-wheel drive or four-wheel drive?
The VALMET 1102 (-4) was built in two-wheel drive (2WD) and four-wheel drive (4WD) versions, depending on configuration.
What PTO does an 1102 (-4) have?
An 1102 (-4) has a 540/1000 rpm rear PTO on a 1 3/8"- 6 splines (Form-A) shaft.
Where this page comes from
Compiled from Traktorenlexikon, “Valmet 1102”.
Sources
Facts taken from these documents, units converted. Numbers beside a figure refer to this list. Licences and attribution
- Traktorenlexikon: Valmet 1102 — CC BY-SA 4.0, WIKIBOOKS-TL-116333 · revision 997283. Wikibooks contributors (Traktorenlexikon). Original document