- Rigid chassis
- WhichTractor size: Utility
- Not independently tested
- 1985–1990
WhichTractor size, not the maker’s category
Derived by WhichTractor from a sourced three-point linkage. How we decide what a machine is
Deutz-Fahr DX 3.80 AS Full specifications
KHD F4L 913 four-cylinder diesel. The manufacturer claimed 74 horsepower. No laboratory has tested one, so there is no measured figure at the shaft.
Engine power, claimed · gross or net not stated
74 hp
55 kW as stated by the source
Not independently tested
Claimed · standard not stated by the source
Source · Traktorenlexikon, “Deutz-Fahr DX 3.80 AS”, claimed
- Weight
- 7,275 lb
- 3-point lift
- 5,291 lb
- Hyd. flow
- 10.6 gpm
- Top speed
- 18.6 mph
Deutz-Fahr DX 3.80 AS specs: key facts
The Deutz-Fahr DX 3.80 AS was built from 1985 to 1990.
The Deutz-Fahr DX 3.80 AS has a claimed engine power (gross or net not stated) of 55 kW (74 hp); it has no measured PTO figure.
The Deutz-Fahr DX 3.80 AS is four-wheel drive (4WD).
The Deutz-Fahr DX 3.80 AS has a KHD F4L 913 engine, a 4-cylinder 4.09 L diesel unit.Source 2
The Deutz-Fahr DX 3.80 AS weighs 3,300 kg (7,275 lb) unladen.
The Deutz-Fahr DX 3.80 AS has an independent rear PTO running at 540/1000 rpm.
The three-point hitch of the Deutz-Fahr DX 3.80 AS lifts 2,400 kg (5,291 lb) at the lower-link ends.
The hydraulic pump of the Deutz-Fahr DX 3.80 AS delivers 40.0 L/min (10.6 gpm).
Source · Traktorenlexikon, “Deutz-Fahr DX 3.80 AS”
How much horsepower does a DX 3.80 AS have?
The only figure for the DX 3.80 AS is 74 hp (55 kW) of claimed engine power, gross or net not stated, no test standard stated — not power at the shaft.
Source · Traktorenlexikon, “Deutz-Fahr DX 3.80 AS”
What engine is in a DX 3.80 AS?
A DX 3.80 AS has a KHD F4L 913, a 4-cylinder 4.09 L diesel engine.
| Make & model | KHD F4L 913Source 2 |
|---|---|
| Cylinders | 4, air-cooledSource 2 |
| Displacement | 249.3 ci · 4.09 LSource 2 |
| Max torque | 192 lb·ft · 260 N·m @ 1,550 rpm |
| Injection | Direct injection |
| Electrical system | 12 V |
Source · Traktorenlexikon, “Deutz-Fahr DX 3.80 AS”
How much will a DX 3.80 AS lift, and what is its hydraulic flow?
A DX 3.80 AS lifts 5,291 lb (2,400 kg) at the lower-link ends.
| System | Open centre |
|---|---|
| Pump flow | 10.6 gpm · 40.0 L/min |
| Pressure | 3,481 psi · 240 bar |
| Lift at ends | 5,291 lb · 2,400 kg |
| Rear PTO | Independent, 540/1000 rpm @ 2,025 engine rpmEngages under load |
| PTO shaft | 1 3/8"-6 splines (Form 1) |
Source · Traktorenlexikon, “Deutz-Fahr DX 3.80 AS”
What transmission does a DX 3.80 AS have?
Transmission specifications for the DX 3.80 AS are below.
| Clutch | Independent dry double clutch |
|---|---|
| Steering | Hydrostatic Danfoss steering |
| Top speed | 18.6 mph · 30 km/h |
Source · Traktorenlexikon, “Deutz-Fahr DX 3.80 AS”
How much does a DX 3.80 AS weigh?
A DX 3.80 AS weighs 7,275 lb (3,300 kg) unladen.
| Unladen weight | 7,275 lb · 3,300 kg |
|---|---|
| Maximum permissible mass | 8,818 lb · 4,000 kg |
| Maximum front axle load | 3,748 lb · 1,700 kg |
| Maximum rear axle load | 6,614 lb · 3,000 kg |
| Wheelbase | 88.6 in · 2,250 mm |
| Length | 148.8 in · 3,780 mm |
| Width | 74.4 in · 1,890 mm |
| Height | 92.9 in · 2,360 mm |
| Ground clearance | 13.4 in · 340 mm |
| Front track | 59.1–65.0 in · 1,500–1,650 mmthe article lists alternatives |
| Rear track | 55.9–75.6 in · 1,420–1,920 mm |
Source · Traktorenlexikon, “Deutz-Fahr DX 3.80 AS”
Which tractors compare with a DX 3.80 AS?
Within 10% of its 66.2 hp at the PTO (claimed), the same type, and first built within 15 years of it.
- Deutz-Fahr DX 4.3066.2 hp PTO, claimed · 1983–1989Side by side with the DX 3.80 AS →
- Ford 6600 (A)66.2 hp PTO, claimed · 1975–1981Side by side with the DX 3.80 AS →
- International Harvester 66666.3 hp PTO, claimed · 1972–1976Side by side with the DX 3.80 AS →
- Lamborghini R-475 (DT)66.2 hp PTO, claimed · 1971–1973Side by side with the DX 3.80 AS →
- Renault 781-4 (S)66.4 hp PTO, claimed · 1977–1985Side by side with the DX 3.80 AS →
- VALMET 80066.4 hp PTO, claimed · 1997–2002Side by side with the DX 3.80 AS →
Everything else people ask
Is a DX 3.80 AS two-wheel drive or four-wheel drive?
The Deutz-Fahr DX 3.80 AS is four-wheel drive (4WD).
What PTO does a DX 3.80 AS have?
A DX 3.80 AS has a independent 540/1000 rpm rear PTO on a 1 3/8"-6 splines (Form 1) shaft.
Where this page comes from
Compiled from Traktorenlexikon, “Deutz-Fahr DX 3.80 AS”; and Traktorenlexikon, “Deutz-Fahr DX 3.90”.
Sources
Facts taken from these documents, units converted. Numbers beside a figure refer to this list. Licences and attribution
- Traktorenlexikon: Deutz-Fahr DX 3.80 AS — CC BY-SA 4.0, WIKIBOOKS-TL-102987 · revision 1023419. Wikibooks contributors (Traktorenlexikon). Original document
- Traktorenlexikon: Deutz-Fahr DX 3.90 — CC BY-SA 4.0, WIKIBOOKS-TL-32890 · revision 1059337. Wikibooks contributors (Traktorenlexikon). Original document