- Rigid chassis
- WhichTractor size: Utility
- Not independently tested
- 1958–1962
- 24,490 built
WhichTractor size, not the maker’s category
Derived by WhichTractor from a sourced three-point linkage. How we decide what a machine is
International Harvester D-324 Standard Full specifications
INTERNATIONAL-HARVESTER DD-111 three-cylinder diesel. The manufacturer claimed 23.7 horsepower. No laboratory has tested one, so there is no measured figure at the shaft.
Engine power, claimed · gross or net not stated
23.7 hp
17.7 kW as stated by the source
Not independently tested
Claimed · standard not stated by the source
Source · Traktorenlexikon, “McCormick D-324 Standard”, claimed
- Weight
- 3,386 lb
- 3-point lift
- 1,323 lb
- Top speed
- 11.8 mph
International Harvester D-324 Standard specs: key facts
The International Harvester D-324 Standard was built from 1958 to 1962.
The International Harvester D-324 Standard has a claimed engine power (gross or net not stated) of 17.7 kW (23.7 hp); it has no measured PTO figure.
The International Harvester D-324 Standard is two-wheel drive (2WD).
The International Harvester D-324 Standard has a INTERNATIONAL-HARVESTER DD-111 engine, a 3-cylinder 1.83 L diesel unit.Source 1
The International Harvester D-324 Standard weighs 1,536 kg (3,386 lb) unladen.
The International Harvester D-324 Standard has a dependent rear PTO running at 540 rpm.
The three-point hitch of the International Harvester D-324 Standard lifts 600 kg (1,323 lb) at the lower-link ends.
Source · Traktorenlexikon, “McCormick D-324 Standard”
How much horsepower does a D-324 Standard have?
The only figure for the D-324 Standard is 23.7 hp (17.7 kW) of claimed engine power, gross or net not stated, no test standard stated — not power at the shaft.
Source · Traktorenlexikon, “McCormick D-324 Standard”
What engine is in a D-324 Standard?
A D-324 Standard has an INTERNATIONAL-HARVESTER DD-111, a 3-cylinder 1.83 L diesel engine.
| Make & model | INTERNATIONAL-HARVESTER DD-111 |
|---|---|
| Cylinders | 3, liquid-cooledSource 2 |
| Displacement | 111.4 ci · 1.83 L |
| Max torque | 73 lb·ft · 99 N·m @ 1,200 rpmSource 2 |
| Electrical system | 12 VSource 2 |
Source · Traktorenlexikon, “McCormick D-324 Farmall”
How much will a D-324 Standard lift?
A D-324 Standard lifts 1,323 lb (600 kg) at the lower-link ends of its Category 1 three-point hitch.
| Hitch category | Category 1 |
|---|---|
| Lift at ends | 1,323 lb · 600 kg |
| Rear PTO | Dependent, transmission-driven, 540 rpmGround-speed PTO available |
Source · Traktorenlexikon, “McCormick D-324 Standard”
What transmission does a D-324 Standard have?
Transmission specifications for the D-324 Standard are below.
| Clutch | Pedal operated dry single plate clutch |
|---|---|
| Brakes | Pedal operated disc brake positioned on differential half shafts |
| Steering | Mechanically operated steering |
| Top speed | 11.8 mph · 19 km/h |
Source · Traktorenlexikon, “McCormick D-324 Standard”
How much does a D-324 Standard weigh?
A D-324 Standard weighs 3,386 lb (1,536 kg) unladen.
| Unladen weight | 3,386 lb · 1,536 kg |
|---|---|
| Wheelbase | 70.0 in · 1,779 mm |
| Length | 108.3 in · 2,750 mm |
| Width | 64.6 in · 1,640 mm |
| Height | 61.0 in · 1,550 mm |
| Ground clearance | 15.1 in · 383 mm |
| Front track | 49.2–59.1 in · 1,250–1,500 mmthe article lists alternatives |
| Rear track | 49.2–74.8 in · 1,250–1,900 mm |
| Turning radius, braked | 9.2 ft · 2.80 m |
Source · Traktorenlexikon, “McCormick D-324 Standard”
Which tractors compare with a D-324 Standard?
Within 10% of its 22.6 hp at the PTO (claimed), the same type, and first built within 15 years of it.
- Fiat 250 (DT)22.6 hp PTO, claimed · 1968–1974Side by side with the D-324 Standard →
- SOMECA 250 (DT)22.6 hp PTO, claimed · 1968–1971Side by side with the D-324 Standard →
- Güldner AB23 hp PTO, claimed · 1958–1959Side by side with the D-324 Standard →
- Güldner A 2 BL23 hp PTO, claimed · 1959–1960Side by side with the D-324 Standard →
- Fahr D 180 H23 hp PTO, claimed · 1954–1959Side by side with the D-324 Standard →
- Fahr D 28 UW23 hp PTO, claimed · 1948–1951Side by side with the D-324 Standard →
Everything else people ask
Is a D-324 Standard two-wheel drive or four-wheel drive?
The International Harvester D-324 Standard is two-wheel drive (2WD).
What PTO does a D-324 Standard have?
A D-324 Standard has a dependent 540 rpm rear PTO.
What serial numbers does a D-324 Standard carry?
The source prints serial numbers NT 225.001 to NT 249.495 for the FARMALL and STANDARD. It also records 2 changes by serial number. It does not say whether that is the tractor’s or the engine’s number, and we never work out a year from a serial number.
Where this page comes from
Compiled from Traktorenlexikon, “McCormick D-324 Farmall”; and Traktorenlexikon, “McCormick D-324 Standard”.
Sources
Facts taken from these documents, units converted. Numbers beside a figure refer to this list. Licences and attribution
- Traktorenlexikon: McCormick D-324 Farmall — CC BY-SA 4.0, WIKIBOOKS-TL-118023 · revision 1056722. Wikibooks contributors (Traktorenlexikon). Original document
- Traktorenlexikon: McCormick D-324 Standard — CC BY-SA 4.0, WIKIBOOKS-TL-118057 · revision 1056723. Wikibooks contributors (Traktorenlexikon). Original document