- Rigid chassis
- WhichTractor size: Standard-size
- No lab test on file
- 1984–1989
- 62 built
WhichTractor size, not the maker’s category
Derived by WhichTractor from a sourced three-point linkage. How we decide what a machine is
Deutz-Fahr DX 7.10A specs: hp, weight, years
KHD BF6L 913.118/2 six-cylinder diesel. The manufacturer claimed 157.0 horsepower. No laboratory has tested one, so there is no measured figure at the shaft.
Engine power, claimed · gross or net not stated
157.0 hp
117.1 kW as stated by the source
No lab test on file
Claimed · standard not stated by the source
Source · Traktorenlexikon, “Deutz-Fahr DX 7.10”, claimed
This is the maker’s own figure, measured at the engine. Power at the PTO is lower — by how much, for this machine, nobody has measured.
- Weight
- 13,206 lb
- 3-point lift
- 17,196 lb
- Hyd. flow
- 16.2 gpm
- Top speed
- 18.6 mph
Deutz-Fahr DX 7.10A specs: key facts
The Deutz-Fahr DX 7.10A was built from 1984 to 1989.
The Deutz-Fahr DX 7.10A has a claimed engine power (gross or net not stated) of 117.1 kW (157.0 hp); it has no measured PTO figure.
The Deutz-Fahr DX 7.10A was offered in two-wheel-drive and four-wheel-drive versions.
The Deutz-Fahr DX 7.10A has a KHD BF6L 913.118/2 engine, a 6-cylinder 6.13 L diesel unit.
The Deutz-Fahr DX 7.10A weighs 5,990 kg (13,206 lb) unladen.
The Deutz-Fahr DX 7.10A has an independent rear PTO running at 1000 rpm.
The three-point hitch of the Deutz-Fahr DX 7.10A lifts 7,800 kg (17,196 lb) at the lower-link ends.
The hydraulic pump of the Deutz-Fahr DX 7.10A delivers 61.2 L/min (16.2 gpm).
Source · Traktorenlexikon, “Deutz-Fahr DX 7.10”
How does the DX 7.10A compare with its class?
- Limitation:
A 150 L fuel tank is low for its class — 45% below the median of 275 L across the 182 machines within 10% of its power that hold this figure.
Derived by WhichTractor from 186 comparable records. How we work this out
How much horsepower does a DX 7.10A have?
The only figure for the DX 7.10A is 157.0 hp (117.1 kW) of claimed engine power, gross or net not stated, no test standard stated — not power at the shaft.
Source · Traktorenlexikon, “Deutz-Fahr DX 7.10”
What engine is in a DX 7.10A?
A DX 7.10A has a KHD BF6L 913.118/2, a 6-cylinder 6.13 L diesel engine.
| Make & model | KHD BF6L 913.118/2 |
|---|---|
| Cylinders | 6, air-cooled |
| Displacement | 374.0 ci · 6.13 L |
| Max torque | 415 lb·ft · 563 N·m @ 1,799 rpm |
| Electrical system | 12 V |
Source · Traktorenlexikon, “Deutz-Fahr DX 7.10”
How much will a DX 7.10A lift, and what is its hydraulic flow?
A DX 7.10A lifts 17,196 lb (7,800 kg) at the lower-link ends.
| Pump flow | 16.2 gpm · 61.2 L/min |
|---|---|
| Pressure | 3,481 psi · 240 bar |
| Lift at ends | 17,196 lb · 7,800 kg |
| Rear PTO | Independent, 1000 rpm @ 2,095 engine rpmEngages under load |
Source · Traktorenlexikon, “Deutz-Fahr DX 7.10”
What transmission does a DX 7.10A have?
Transmission specifications for the DX 7.10A are below.
| Clutch | Independent dry two-plate clutch |
|---|---|
| Brakes | Hydraulically operated wet Girling-Goimpd disc brakes acting on differential side shafts |
| Steering | Hydrostatic ZF steering |
| Top speed | 18.6 mph · 30 km/h |
Source · Traktorenlexikon, “Deutz-Fahr DX 7.10”
How much does a DX 7.10A weigh?
A DX 7.10A weighs 13,206 lb (5,990 kg) unladen.
| Unladen weight | 13,206 lb · 5,990 kg |
|---|---|
| Maximum permissible mass | 18,739 lb · 8,500 kg |
| Maximum front axle load | 7,937 lb · 3,600 kg |
| Maximum rear axle load | 14,330 lb · 6,500 kg |
| Wheelbase | 111.3 in · 2,826 mm |
| Length | 187.8 in · 4,770 mm |
| Width | 93.3 in · 2,370 mm |
| Height | 107.5 in · 2,730 mm |
| Ground clearance | 19.3 in · 490 mm |
| Front track | 72.7–76.9 in · 1,846–1,952 mm |
| Rear track | 70.9–78.7 in · 1,800–2,000 mm |
| Turning radius, braked | 22.0 ft · 6.72 m |
Source · Traktorenlexikon, “Deutz-Fahr DX 7.10”
What oil does a DX 7.10A take, and how much?
A DX 7.10A engine takes 19.5 qt (18.5 L). Single source, not independently verified — always confirm against the operator’s manual for your machine.
| System | Capacity |
|---|---|
| Engine oil | 19.5 qt · 18.5 LSource: Traktorenlexikon, “Deutz-Fahr DX 7.10” · single source, not independently verified |
| Transmission | 82.4 qt · 78 LSource: Traktorenlexikon, “Deutz-Fahr DX 7.10” · single source, not independently verified |
| Front axle | 9.5 qt · 9.0 LSource: Traktorenlexikon, “Deutz-Fahr DX 7.10” · single source, not independently verified |
Always confirm against the operator’s manual for your machine before service.
Which tractors compare with a DX 7.10A?
Within 10% of its 157.0 hp of claimed engine power, the same type, and first built within 15 years of it.
- DEUTZ-ALLIS DX 7.10157.0 hp engine, claimed · 1984–1986Side by side with the DX 7.10A →
- SAME Hercules 160156.8 hp engine, claimed · 1979–1983Side by side with the DX 7.10A →
- SAME Titan 160156.8 hp engine, claimed · 1991–1998Side by side with the DX 7.10A →
- ZETOR 16145157.8 hp engine, claimed · 1984–1990Side by side with the DX 7.10A →
- VALMET 8550157.8 hp engine, claimed · 1995–2001Side by side with the DX 7.10A →
- New Holland 8560A157.8 hp engine, claimed · 1996–1999Side by side with the DX 7.10A →
Common questions about the Deutz-Fahr DX 7.10A
Is a DX 7.10A two-wheel drive or four-wheel drive?
The Deutz-Fahr DX 7.10A was offered in two-wheel-drive and four-wheel-drive versions.
What PTO does a DX 7.10A have?
A DX 7.10A has a independent 1000 rpm rear PTO.
Sources and how this page was built
Compiled from Traktorenlexikon, “Deutz-Fahr DX 7.10”.
Sources
Facts taken from these documents, units converted. Numbers beside a figure refer to this list. Licences and attribution
- Traktorenlexikon: Deutz-Fahr DX 7.10 — CC BY-SA 4.0, WIKIBOOKS-TL-74835 · revision 1089899. Wikibooks contributors (Traktorenlexikon). Original document