- Rigid chassis
- WhichTractor size: Utility
- Not independently tested
- 1997–2002
WhichTractor size, not the maker’s category
Derived by WhichTractor from a sourced three-point linkage. How we decide what a machine is
VALMET 800 Full specifications
VALMET 420 DS or DSRE four-cylinder diesel. The manufacturer claimed 79 horsepower. No laboratory has tested one, so there is no measured figure at the shaft.
Engine power, claimed · gross or net not stated
79 hp
59 kW as stated by the source
Not independently tested
Claimed · standard not stated by the source
Source · Traktorenlexikon, “Valmet 800”, claimed
- Weight
- 7,341 lb
- 3-point lift
- 7,419 lb
- Hyd. flow
- 14.7 gpm
- Top speed
- 18.6–24.9 mph
VALMET 800 specs: key facts
The VALMET 800 was built from 1997 to 2002.
The VALMET 800 has a claimed engine power (gross or net not stated) of 59 kW (79 hp); it has no measured PTO figure.
The VALMET 800 was built in two-wheel drive (2WD) and four-wheel drive (4WD) versions, depending on configuration.
The VALMET 800 has a VALMET 420 DS or DSRE engine, a 4-cylinder 4.40 L diesel unit.
The VALMET 800 weighs 3,330 kg (7,341 lb) unladen.
The VALMET 800 has an independent rear PTO running at 540E/540 rpm.
The three-point hitch of the VALMET 800 lifts 3,365 kg (7,419 lb) at the lower-link ends.
The hydraulic pump of the VALMET 800 delivers 55.7 L/min (14.7 gpm).
Source · Traktorenlexikon, “Valmet 800”
How much horsepower does an 800 have?
The only figure for the 800 is 79 hp (59 kW) of claimed engine power, gross or net not stated, no test standard stated — not power at the shaft.
Source · Traktorenlexikon, “Valmet 800”
What engine is in an 800?
An 800 has a VALMET 420 DS or DSRE, a 4-cylinder 4.40 L diesel engine.
| Make & model | VALMET 420 DS or DSRE |
|---|---|
| Cylinders | 4, liquid-cooled |
| Displacement | 268.3 ci · 4.40 L |
| Electrical system | 12 V |
Source · Traktorenlexikon, “Valmet 800”
How much will an 800 lift, and what is its hydraulic flow?
An 800 lifts 7,419 lb (3,365 kg) at the lower-link ends of its Category 2 three-point hitch.
| System | Constant flow |
|---|---|
| Pump flow | 14.7 gpm · 55.7 L/min |
| Pressure | 2,901 psi · 200 bar |
| Hitch category | Category 2 |
| Lift at ends | 7,419 lb · 3,365 kg |
| Rear PTO | Independent, engine-driven, 540E/540 rpm @ 1,890 engine rpmEngages under load |
| PTO shaft | 1 3/8"- 6 splines and 1 3/8"- 21 part |
Source · Traktorenlexikon, “Valmet 800”
What transmission does an 800 have?
Transmission specifications for the 800 are below.
| Clutch | Dry LuK double clutch |
|---|---|
| Steering | Hydrostatic steering |
| Top speed | 18.6–24.9 mph · 30–40 km/hthe article lists alternatives |
Source · Traktorenlexikon, “Valmet 800”
How much does an 800 weigh?
An 800 weighs 7,341 lb (3,330 kg) unladen.
| Unladen weight | 7,341 lb · 3,330 kgtwo-wheel-drive version |
|---|---|
| Wheelbase | 88.3 in · 2,244 mmtwo-wheel-drive version |
| Length | 152.6 in · 3,877 mmtwo-wheel-drive version |
| Width | 85.7 in · 2,177 mm |
| Height | 106.3 in · 2,700 mm |
| Ground clearance | 19.9 in · 505 mmtwo-wheel-drive version |
| Front track | 55.5–63.4 in · 1,410–1,610 mmtwo-wheel-drive version |
| Rear track | 55.5–83.1 in · 1,410–2,110 mm |
| Turning radius, braked | 15.7 ft · 4.80 mtwo-wheel-drive version |
Source · Traktorenlexikon, “Valmet 800”
Which tractors compare with an 800?
Within 10% of its 66.4 hp at the PTO (claimed), the same type, and first built within 15 years of it.
- John Deere 5403 (A)66.2 hp PTO, claimed · 2007–2008Side by side with the 800 →
- Deutz-Fahr DX 3.80 AS66.2 hp PTO, claimed · 1985–1990Side by side with the 800 →
- Deutz-Fahr DX 4.3066.2 hp PTO, claimed · 1983–1989Side by side with the 800 →
- Renault 80-14 F66.6 hp PTO, claimed · 1986–1999Side by side with the 800 →
- Fiat TL 80 (DT)66.0 hp PTO, claimed · 1998–2004Side by side with the 800 →
- New Holland TL 80 (A)66.0 hp PTO, claimed · 1998–2004Side by side with the 800 →
Everything else people ask
Is an 800 two-wheel drive or four-wheel drive?
The VALMET 800 was built in two-wheel drive (2WD) and four-wheel drive (4WD) versions, depending on configuration.
What PTO does an 800 have?
An 800 has a independent 540E/540 rpm rear PTO on a 1 3/8"- 6 splines and 1 3/8"- 21 part shaft.
Where this page comes from
Compiled from Traktorenlexikon, “Valmet 800”.
Sources
Facts taken from these documents, units converted. Numbers beside a figure refer to this list. Licences and attribution
- Traktorenlexikon: Valmet 800 — CC BY-SA 4.0, WIKIBOOKS-TL-116444 · revision 998941. Wikibooks contributors (Traktorenlexikon). Original document