- Vehicle type: unspecified
- Rigid chassis
- WhichTractor size: Utility
- No lab test on file
- 1957–1960
- 26,000 built
It was ranked on an engine power figure whose source does not say gross or net. WhichTractor size, not the maker’s category
We looked and the record does not say what this machine is. How we decide what a machine is
Hanomag C 112 specs: hp, weight, years
The manufacturer claimed 11.8 horsepower. No laboratory has tested one, so there is no measured figure at the shaft.
Engine power, claimed · gross or net not stated
11.8 hp
8.8 kW as stated by the source
No lab test on file
Claimed · standard not stated by the source
Source · Traktorenlexikon, “Hanomag C 112”, claimed
This is the maker’s own figure, measured at the engine. Power at the PTO is lower — by how much, for this machine, nobody has measured.
- Weight
- 1,764 lb
- Hyd. flow
- 2.4 gpm
- Top speed
- 11.8 mph
Hanomag C 112 specs: key facts
The Hanomag C 112 was built from 1957 to 1960.
The Hanomag C 112 has a claimed engine power (gross or net not stated) of 8.8 kW (11.8 hp); it has no measured PTO figure.
The Hanomag C 112 is two-wheel drive (2WD).
The Hanomag C 112 weighs 800 kg (1,764 lb) unladen.
The Hanomag C 112 has a rear PTO running at 1484 rpm.
The hydraulic pump of the Hanomag C 112 delivers 9.0 L/min (2.4 gpm).
Source · Traktorenlexikon, “Hanomag C 112”
How does the C 112 compare with its class?
We will not rate this machine against its class. Only 23 published tractors sit within 10% of its 8.8 kW — too few to say what is normal.
Derived by WhichTractor. How we work this out
How much horsepower does a C 112 have?
The only figure for the C 112 is 11.8 hp (8.8 kW) of claimed engine power, gross or net not stated, no test standard stated — not power at the shaft.
Source · Traktorenlexikon, “Hanomag C 112”
How much will a C 112 lift, and what is its hydraulic flow?
Hydraulic and PTO specifications for the C 112 are below.
| Pump flow | 2.4 gpm · 9.0 L/min |
|---|---|
| Pressure | 1,138 psi · 78 bar |
| Rear PTO | 1484 rpm |
Source · Traktorenlexikon, “Hanomag C 112”
What transmission does a C 112 have?
Transmission specifications for the C 112 are below.
| Clutch | standard single dry clutch built into the flywheel |
|---|---|
| Brakes | Mechanically lockable drum brakes, rear with dual brake foot pedal system |
| Steering | worm drive fastened to the frame |
| Top speed | 11.8 mph · 19 km/h |
Source · Traktorenlexikon, “Hanomag C 112”
How much does a C 112 weigh?
A C 112 weighs 1,764 lb (800 kg) unladen.
| Unladen weight | 1,764 lb · 800 kg |
|---|---|
| Wheelbase | 70.9 in · 1,800 mm |
| Length | 107.5 in · 2,730 mm |
| Width | 58.3–65.7 in · 1,480–1,670 mm |
| Height | 63.0–65.0 in · 1,600–1,650 mm |
| Ground clearance | 16.3 in · 415 mm |
| Front track | 50.4–59.6 in · 1,280–1,514 mmthe article lists alternatives |
| Rear track | 49.2–58.3 in · 1,250–1,480 mmthe article lists alternatives |
| Turning radius, braked | 7.9 ft · 2.40 m |
Source · Traktorenlexikon, “Hanomag C 112”
Which tractors compare with a C 112?
Within 10% of its 11.8 hp of claimed engine power, the same type, and first built within 15 years of it.
- Hanomag R 12 KB11.8 hp engine, claimed · 1954–1957Side by side with the C 112 →
- Hermann Zanker KG M 111.8 hp engine, claimed · 1949–1951Side by side with the C 112 →
- MASSEY-HARRIS Pony 1111.0 hp engine, claimed · 1947–1957Side by side with the C 112 →
- Kramer KA 11010.9 hp engine, claimed · 1956–1958Side by side with the C 112 →
Common questions about the Hanomag C 112
Is a C 112 two-wheel drive or four-wheel drive?
The Hanomag C 112 is two-wheel drive (2WD).
What PTO does a C 112 have?
A C 112 has a 1484 rpm rear PTO.
Sources and how this page was built
Compiled from Traktorenlexikon, “Hanomag C 112”.
Sources
Facts taken from these documents, units converted. Numbers beside a figure refer to this list. Licences and attribution
- Traktorenlexikon: Hanomag C 112 — CC BY-SA 4.0, WIKIBOOKS-TL-58529 · revision 958927. Wikibooks contributors (Traktorenlexikon). Original document