- Crawler
- WhichTractor size: Utility
- Not independently tested
- 1968–1975
It was ranked on an engine power figure whose source does not say gross or net. WhichTractor size, not the maker’s category
Derived by WhichTractor from a sourced three-point linkage. How we decide what a machine is
Fiat 455 C Full specifications
FIAT-IVECO 8035.02.210 or 310 three-cylinder diesel. The manufacturer claimed 43.4 horsepower. No laboratory has tested one, so there is no measured figure at the shaft.
Engine power, claimed · gross or net not stated
43.4 hp
32.4 kW as stated by the source
Not independently tested
Claimed · standard not stated by the source
Source · Traktorenlexikon, “Fiat 455 C”, claimed
- Weight
- 4,718 lb
- Hyd. flow
- 4.7 gpm
- Top speed
- 6.8 mph
Fiat 455 C specs: key facts
The Fiat 455 C was built from 1968 to 1975.
The Fiat 455 C has a claimed engine power (gross or net not stated) of 32.4 kW (43.4 hp); it has no measured PTO figure.
The Fiat 455 C is a tracked machine.
The Fiat 455 C has a FIAT-IVECO 8035.02.210 or 310 engine, a 3-cylinder 2.59 L diesel unit.
The Fiat 455 C weighs 2,140 kg (4,718 lb) unladen.
The Fiat 455 C has a rear PTO running at 540 rpm.
The hydraulic pump of the Fiat 455 C delivers 17.8 L/min (4.7 gpm).
Source · Traktorenlexikon, “Fiat 455 C”
How much horsepower does a 455 C have?
The only figure for the 455 C is 43.4 hp (32.4 kW) of claimed engine power, gross or net not stated, no test standard stated — not power at the shaft.
Source · Traktorenlexikon, “Fiat 455 C”
What engine is in a 455 C?
A 455 C has a FIAT-IVECO 8035.02.210 or 310, a 3-cylinder 2.59 L diesel engine.
| Make & model | FIAT-IVECO 8035.02.210 or 310 |
|---|---|
| Cylinders | 3, liquid-cooled |
| Displacement | 158.2 ci · 2.59 L |
| Electrical system | 12 V |
Source · Traktorenlexikon, “Fiat 455 C”
How much will a 455 C lift, and what is its hydraulic flow?
Hydraulic and PTO specifications for the 455 C are below.
| Pump flow | 4.7 gpm · 17.8 L/min |
|---|---|
| Pressure | 2,843 psi · 196 bar |
| Hitch category | Category 1 |
| Rear PTO | 540 rpm @ 1,970 engine rpm |
| PTO shaft | 1 3/8"- 6 splines |
Source · Traktorenlexikon, “Fiat 455 C”
What transmission does a 455 C have?
Transmission specifications for the 455 C are below.
| Clutch | Hand lever operated dry single disc clutch with dead center engagement |
|---|---|
| Top speed | 6.8 mph · 11 km/h |
Source · Traktorenlexikon, “Fiat 455 C”
How much does a 455 C weigh?
A 455 C weighs 4,718 lb (2,140 kg) unladen.
| Unladen weight | 4,718 lb · 2,140 kg |
|---|---|
| Wheelbase | 50.9 in · 1,293 mm |
| Length | 105.3 in · 2,675 mm |
| Width | 50.9 in · 1,292 mm |
| Height | 47.6 in · 1,210 mm |
| Ground clearance | 9.8 in · 250 mm |
| Front track | 39.8 in · 1,010 mmWikibooks gives one track for both axles |
| Rear track | 39.8 in · 1,010 mmWikibooks gives one track for both axles |
Source · Traktorenlexikon, “Fiat 455 C”
Which tractors compare with a 455 C?
Within 10% of its 43.4 hp of claimed engine power, the same type, and first built within 15 years of it.
- ZETOR Super-P41.4 hp engine, claimed · 1956–1958Side by side with the 455 C →
- Fiat 411 C (CI)39.4 hp engine, claimed · 1958–1964Side by side with the 455 C →
- Fiat 431 C39.4 hp engine, claimed · 1958–1964Side by side with the 455 C →
- Fiat 451 C39.4 hp engine, claimed · 1958–1964Side by side with the 455 C →
Everything else people ask
Is a 455 C two-wheel drive or four-wheel drive?
The Fiat 455 C is a tracked machine.
What PTO does a 455 C have?
A 455 C has a 540 rpm rear PTO on a 1 3/8"- 6 splines shaft.
Where this page comes from
Compiled from Traktorenlexikon, “Fiat 455 C”.
Sources
Facts taken from these documents, units converted. Numbers beside a figure refer to this list. Licences and attribution
- Traktorenlexikon: Fiat 455 C — CC BY-SA 4.0, WIKIBOOKS-TL-121933 · revision 1076581. Wikibooks contributors (Traktorenlexikon). Original document