- Vehicle type: unspecified
- Rigid chassis
- WhichTractor size: Standard-size
- Not independently tested
- 1954–1957
- 69 built
It was ranked on an engine power figure whose source does not say gross or net. WhichTractor size, not the maker’s category
We looked and the record does not say what this machine is. How we decide what a machine is
Fahr D 400 C Full specifications
KHD F3L 514 three-cylinder diesel. The manufacturer claimed 44.1 horsepower. No laboratory has tested one, so there is no measured figure at the shaft.
Engine power, claimed · gross or net not stated
44.1 hp
32.9 kW as stated by the source
Not independently tested
Claimed · standard not stated by the source
Source · Traktorenlexikon, “Fahr D 400 C”, claimed
- Weight
- 5,666 lb
- Hyd. flow
- 4.9 gpm
- Top speed
- 12.9–18.6 mph
Fahr D 400 C specs: key facts
The Fahr D 400 C was built from 1954 to 1957.
The Fahr D 400 C has a claimed engine power (gross or net not stated) of 32.9 kW (44.1 hp); it has no measured PTO figure.
The Fahr D 400 C is two-wheel drive (2WD).
The Fahr D 400 C has a KHD F3L 514 engine, a 3-cylinder 3.99 L diesel unit.Source 2
The Fahr D 400 C weighs 2,570 kg (5,666 lb) unladen.
The Fahr D 400 C has a dependent rear PTO running at 575 rpm.
The hydraulic pump of the Fahr D 400 C delivers 18.5 L/min (4.9 gpm).
Source · Traktorenlexikon, “Fahr D 400 C”
How much horsepower does a D 400 C have?
The only figure for the D 400 C is 44.1 hp (32.9 kW) of claimed engine power, gross or net not stated, no test standard stated — not power at the shaft.
Source · Traktorenlexikon, “Fahr D 400 C”
What engine is in a D 400 C?
A D 400 C has a KHD F3L 514, a 3-cylinder 3.99 L diesel engine.
| Make & model | KHD F3L 514Source 2 |
|---|---|
| Cylinders | 3, air-cooledSource 2 |
| Displacement | 243.5 ci · 3.99 LSource 2 |
| Max torque | 164 lb·ft · 223 N·m @ 1,100 rpm |
| Electrical system | 12 V |
Source · Traktorenlexikon, “Fahr D 400 C”
How much will a D 400 C lift, and what is its hydraulic flow?
Hydraulic and PTO specifications for the D 400 C are below.
| Pump flow | 4.9 gpm · 18.5 L/min |
|---|---|
| Pressure | 1,707 psi · 118 bar |
| Rear PTO | Dependent, transmission-driven, 575 rpm |
| PTO shaft | 29 x 34,9 x 8,7 mm |
Source · Traktorenlexikon, “Fahr D 400 C”
What transmission does a D 400 C have?
Transmission specifications for the D 400 C are below.
| Clutch | Pedal operated dry Fichtel & Sachs single-plate clutch |
|---|---|
| Steering | ZF independent wheel steering |
| Top speed | 12.9–18.6 mph · 20.8–30.0 km/h |
Source · Traktorenlexikon, “Fahr D 400 C”
How much does a D 400 C weigh?
A D 400 C weighs 5,666 lb (2,570 kg) unladen.
| Unladen weight | 5,666 lb · 2,570 kg |
|---|---|
| Maximum permissible mass | 8,818 lb · 4,000 kg |
| Maximum front axle load | 3,086 lb · 1,400 kg |
| Maximum rear axle load | 5,952 lb · 2,700 kg |
| Wheelbase | 82.7 in · 2,100 mm |
| Length | 134.3 in · 3,410 mm |
| Width | 73.4 in · 1,865 mm |
| Height | 91.5 in · 2,325 mm |
| Ground clearance | 16.2 in · 412 mm |
| Front track | 63.0–74.8 in · 1,600–1,900 mm |
| Rear track | 59.1–69.0 in · 1,500–1,752 mmthe article lists alternatives |
| Turning radius, braked | 12.0 ft · 3.65 m |
Source · Traktorenlexikon, “Fahr D 400 C”
Which tractors compare with a D 400 C?
Within 10% of its 44.1 hp of claimed engine power, the same type, and first built within 15 years of it.
- Güldner G 45 (S)44.1 hp engine, claimed · 1965–1969Side by side with the D 400 C →
- Güldner G 45 A (S)44.1 hp engine, claimed · 1965–1969Side by side with the D 400 C →
- Hürlimann D-100 Allrad44.1 hp engine, claimed · 1966–1971Side by side with the D 400 C →
- Fiat 45-R44.4 hp engine, claimed · from 1952Side by side with the D 400 C →
- SOMECA SOM-4044.4 hp engine, claimed · 1957–1959Side by side with the D 400 C →
- SOMECA SOM-40 B44.4 hp engine, claimed · 1959–1960Side by side with the D 400 C →
Everything else people ask
Is a D 400 C two-wheel drive or four-wheel drive?
The Fahr D 400 C is two-wheel drive (2WD).
What PTO does a D 400 C have?
A D 400 C has a dependent 575 rpm rear PTO on a 29 x 34,9 x 8,7 mm shaft.
Where this page comes from
Compiled from Traktorenlexikon, “Fahr D 45 L”; and Traktorenlexikon, “Fahr D 400 C”.
Sources
Facts taken from these documents, units converted. Numbers beside a figure refer to this list. Licences and attribution
- Traktorenlexikon: Fahr D 400 C — CC BY-SA 4.0, WIKIBOOKS-TL-43359 · revision 1078528. Wikibooks contributors (Traktorenlexikon). Original document
- Traktorenlexikon: Fahr D 45 L — CC BY-SA 4.0, WIKIBOOKS-TL-43354 · revision 1078527. Wikibooks contributors (Traktorenlexikon). Original document