9 material differences · fewer than 12
Tractor oneAGCO-ALLIS 76001991–1996No measured PTO figureTractor twoLandini 10800 (DT)1987–2000No measured PTO figure
Which should you choose?
Read our verdict on the 7600 and the 10800 (DT) → It is generated from the rows below by a fixed, versioned rule set, and names the figure behind every call.
Field by field
9 material differences · 7 fields identical or within 5%, which is not counted as material
| Field | 7600 | 10800 (DT) | Gap |
|---|---|---|---|
| Engine | |||
| Engine power, claimed claimed | 95.6 hp | 95.7 hp | — |
| Engine declared | S.L.H. 1055 P | PERKINS TW 6.354-4 | differs |
| Displacement declared | 5.19 L | 5.80 L | +12% 10800 (DT) |
| Maximum torque declared | 242 lb·ft · 328 N·m | 245 lb·ft · 332 N·m | — |
| Transmission | |||
| Top speed declared | 18.6 mph · 30 km/h | 18.6 mph · 30 km/h | — |
| Clutch declared | pedal operated dry SLH double clutch | pedal-operated dry single-disc clutch | differs |
| Hydraulics & hitch | |||
| Hydraulic centre declared | Open centre | — | — |
| Pump flow declared | 16.9 gpm · 64.0 L/min | 13.5 gpm · 51.2 L/min | +25% 7600 |
| Pressure declared | 1,740 psi · 120 bar | 2,901 psi · 200 bar | +67% 10800 (DT) |
| Rear PTO speeds declared | 540/1000 rpm | 540/1000 rpm | — |
| Weight & dimensions | |||
| Unladen weight declared | 8,598 lb · 3,900 kg | 9,480 lb · 4,300 kg | +10% 10800 (DT) |
| Maximum permissible mass declared | 11,464 lb · 5,200 kg | 15,432 lb · 7,000 kg | +35% 10800 (DT) |
| Wheelbase declared | 104.6 in · 2,657 mm | 106.1 in · 2,696 mm | — |
| Length declared | 168.2 in · 4,272 mm | 175.2 in · 4,450 mm | — |
| Width declared | 84.0 in · 2,134 mm | 83.9 in · 2,130 mm | — |
| Ground clearance declared | 17.6 in · 447 mm | 16.1 in · 410 mm | +9% 7600 |
| Turning radius, braked declared | 11.0 ft · 3.35 m | — | — |
| Fuel tank declared | 126.8 qt · 120.0 L | 200.8 qt · 190.0 L | +58% 10800 (DT) |
Height is not in this table. It is not one measurement: the sources measure it to different points — over the cab on some machines, over the steering wheel or the exhaust on others — and the same tractor measured two ways can differ by most of a metre. It appears here only when both machines' figures carry the point they were measured to and it is the same point, which is not the case for these two. Each machine's own page prints its height as its source gives it.
AGCO-ALLIS 7600 sources
- Source: Traktorenlexikon, “AGCO-Allis 7600”
Landini 10800 (DT) sources
- Source: Traktorenlexikon, “Landini 10800 DT”