AGCO-ALLIS 7600 or Landini 10800 (DT)?
Which should you choose?
The data can’t decide this. Power at the PTO shaft cannot be compared: the 7600 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 10800 (DT) has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- The AGCO-ALLIS 7600 suits loader and hydraulic implement work better on this data: 25% (12.8 L/min / 3.4 gpm) more hydraulic flow.
- The Landini 10800 (DT) suits road haulage better on this data: 35% (1,800 kg / 3,968 lb) more maximum permissible mass.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | 7600 | 10800 (DT) | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 71.3 kW (95.6 hp)Traktorenlexikon, “AGCO-Allis 7600” | 71.4 kW (95.7 hp)Traktorenlexikon, “Landini 10800 DT” | Not comparableNot comparable on power at the PTO shaft: the 7600 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 10800 (DT) has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the 7600 and the 10800 (DT). |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the 7600 and the 10800 (DT). |
| Which pumps more oil for implements? | 64.0 L/min (16.9 gpm)Traktorenlexikon, “AGCO-Allis 7600” | 51.2 L/min (13.5 gpm)Traktorenlexikon, “Landini 10800 DT” | AheadThe AGCO-ALLIS 7600 has 25% more hydraulic flow (12.8 L/min / 3.4 gpm) than the Landini 10800 (DT) (both pump flow, as stated by the source). |
| Which lifts more on the three-point hitch? | 4,600 kg (10,141 lb)Traktorenlexikon, “AGCO-Allis 7600” | 4,500 kg (9,921 lb)Traktorenlexikon, “Landini 10800 DT” | EvenEven on three-point lift (both lift at the hitch ends, as stated by the source): the difference is under the 10% threshold, too small to call. |
| Which is heavier, for traction? | 3,900 kg (8,598 lb)Traktorenlexikon, “AGCO-Allis 7600” | 4,300 kg (9,480 lb)Traktorenlexikon, “Landini 10800 DT” | Ahead (a fact, not an advantage)The Landini 10800 (DT) is 10% heavier (400 kg / 882 lb) than the AGCO-ALLIS 7600 (both unladen weight, as stated by the source). |
| Which may carry more ballast and load? | 5,200 kg (11,464 lb)Traktorenlexikon, “AGCO-Allis 7600” | 7,000 kg (15,432 lb)Traktorenlexikon, “Landini 10800 DT” | AheadThe Landini 10800 (DT) has 35% higher maximum permissible mass (1,800 kg / 3,968 lb) than the AGCO-ALLIS 7600 (both maximum permissible mass, as stated by the source). |
| Which has the wider choice of gears? | 24Traktorenlexikon, “AGCO-Allis 7600” | 32Traktorenlexikon, “Landini 10800 DT” | AheadThe Landini 10800 (DT) has 33% more forward gears (8 gears) than the AGCO-ALLIS 7600 (both forward gears, as stated by the source). |
| Which offers a creeper range? | YesTraktorenlexikon, “AGCO-Allis 7600” | — | No figureNo call on a creeper range: not stated for the 10800 (DT). |
| Which is faster on the road? | 30 km/h (18.6 mph)Traktorenlexikon, “AGCO-Allis 7600” | 30 km/h (18.6 mph)Traktorenlexikon, “Landini 10800 DT” | EvenEven on top speed (both top speed forward, as stated by the source): the difference is under the 10% threshold, too small to call. |
| Which offers more PTO speeds? | 540/1000 rpmTraktorenlexikon, “AGCO-Allis 7600” | 540/1000 rpmTraktorenlexikon, “Landini 10800 DT” | EvenEven on PTO speeds: the same speeds (540, 1000 rpm). |
| Which PTO runs independently of the ground drive? | independentTraktorenlexikon, “AGCO-Allis 7600” | independentTraktorenlexikon, “Landini 10800 DT” | EvenEven on PTO independence: every PTO is independent. |
| Which drives on both axles? | Two-wheel or four-wheel driveTraktorenlexikon, “AGCO-Allis 7600” | Two-wheel or four-wheel driveTraktorenlexikon, “Landini 10800 DT” | EvenEven on drive: every machine is available with four-wheel drive. |
| Which is newer, and what about parts? | 1991–1996 | 1987–2000 | EvenSame era: production began within 5 years of each other. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The AGCO-ALLIS 7600 has 25% more hydraulic flow (12.8 L/min / 3.4 gpm) than the Landini 10800 (DT) (both pump flow, as stated by the source).
- The Landini 10800 (DT) is 10% heavier (400 kg / 882 lb) than the AGCO-ALLIS 7600 (both unladen weight, as stated by the source).
- The Landini 10800 (DT) has 35% higher maximum permissible mass (1,800 kg / 3,968 lb) than the AGCO-ALLIS 7600 (both maximum permissible mass, as stated by the source).
- The Landini 10800 (DT) has 33% more forward gears (8 gears) than the AGCO-ALLIS 7600 (both forward gears, as stated by the source).
- Even on three-point lift (both lift at the hitch ends, as stated by the source): the difference is under the 10% threshold, too small to call.
- Even on top speed (both top speed forward, as stated by the source): the difference is under the 10% threshold, too small to call.
- Even on PTO speeds: the same speeds (540, 1000 rpm).
- Even on PTO independence: every PTO is independent.
- Even on drive: every machine is available with four-wheel drive.
- Same era: production began within 5 years of each other. We hold no parts-availability data, so there is no call on parts.
- Not comparable on power at the PTO shaft: the 7600 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 10800 (DT) has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power and a creeper range.
← Every figure for both machines, side by side, with sources