- Vehicle type: unspecified
- Rigid chassis
- WhichTractor size: Standard-size
- Lab tested ×1
- 1999–2002
WhichTractor size, not the maker’s category
John Deere 7510 Hydraulics & PTO specifications
19 hydraulics and PTO values on record for the 7510.
Measured at the PTO shaft
115.1 hp
Source · OECD Test 1959, measured
What hydraulics does a 7510 have?
Hydraulic and hitch specifications for the 7510 are below.
| Hydraulic centre | Closed centreSource 1 |
|---|---|
| Hydraulic control | Load sensingOn record for 1 of 3 configurations |
| Pump flow | 26.7 gpm · 101.1 L/minOn record for 1 of 3 configurations |
| Hydraulic pressure | 2,538 psi · 175 barOn record for 1 of 3 configurations |
| Rear remote valves | 4On record for 1 of 3 configurations |
Source · Traktorenlexikon, “John Deere 7510”
What PTO does a 7510 have?
A 7510 has a 540/1000 rpm rear PTO.
| Rear PTO drive | Engine-drivenOn record for 1 of 3 configurations |
|---|---|
| Rear PTO independence | IndependentOn record for 1 of 3 configurations |
| PTO engages under load | YesOn record for 1 of 3 configurations |
| Rear PTO speeds | 540/1000 rpmSource 1 |
| Engine speed at 540 PTO | 2,080 rpmOn record for 1 of 3 configurations |
| Rear PTO shaft | 35 mm, 6 splines / 35 mm, 21 splinesSource 1 |
Source · Traktorenlexikon, “John Deere 7510”
How much power does a 7510 deliver at the PTO?
On OECD Test 1959, the 7510 delivered 115.1 hp (85.8 kW) at the PTO shaft, at rated engine speed.
| PTO power, at rated engine speed | 115.1 hp · 85.8 kWAt 1,003 PTO rpmAt 2,101 engine rpm |
|---|---|
| PTO power, at standard PTO speed | 115.1 hp · 85.8 kWAt 1,003 PTO rpmAt 2,101 engine rpm |
| PTO shaft speed, at maximum power | 908 rpm |
| PTO shaft speed, at rated engine speed | 1,003 rpm |
| PTO shaft speed, at standard PTO speed | 1,003 rpm |
| Hydraulic power, at maximum power | 36.7 hp · 27.4 kW |
| Hydraulic pump delivery, at maximum power | 24.3 gpm · 92.0 L/min |
| Three-point lift force | 10,454 lbf · 46.5 kN |
Source · OECD test report 1959, 2001
Where this page comes from
19 hydraulics and PTO values from OECD test report 1959, 2001; and Traktorenlexikon, “John Deere 7510”.
Sources
Facts taken from these documents, units converted. Numbers beside a figure refer to this list. Licences and attribution
- OECD Code 2 test report 2/1 959: John Deere 7510 — Licence not stated by the publisher; facts cited, OECD-1959 · published 2001-06-19 · retrieved 2026-09-14. OECD. Original document
- Traktorenlexikon: John Deere 7510 — CC BY-SA 4.0, WIKIBOOKS-TL-106379 · revision 877932. Wikibooks contributors (Traktorenlexikon). Original document