10 material differences · fewer than 12
Tractor oneLandini 5860 (DT) TL 38 N/M (TL-38 DT/M)1988–2000No measured PTO figureTractor twoVALMET 205/205-41989–1991No measured PTO figure
Which should you choose?
Read our verdict on the 5860 (DT) TL 38 N/M (TL-38 DT/M) and the 205/205-4 → It is generated from the rows below by a fixed, versioned rule set, and names the figure behind every call.
Field by field
10 material differences · 4 fields identical or within 5%, which is not counted as material
| Field | 5860 (DT) TL 38 N/M (TL-38 DT/M) | 205/205-4 | Gap |
|---|---|---|---|
| Engine | |||
| Engine power, claimed claimed | 47.3 hp | 48 hp | — |
| Engine declared | Perkins D 3152 | VALMET D-27 D 2 | differs |
| Displacement declared | 2.50 L | 2.69 L | +7% 205/205-4 |
| Maximum torque declared | 130 lb·ft · 176 N·m | 129 lb·ft · 175 N·m | — |
| Transmission | |||
| Top speed declared | 18.6 mph · 30 km/h | 18.6 mph · 30 km/h | — |
| Clutch declared | Dry and air-cooled OMG double clutch | Pedal operated dry Fichtel & Sachs single disc clutch | differs |
| Hydraulics & hitch | |||
| Pump flow declared | — | 10.3 gpm · 39.0 L/min | — |
| Pressure declared | 2,756 psi · 190 bar | — | — |
| Rear PTO speeds declared | 540 rpm / 1000 rpm | 540 rpm | differs |
| Weight & dimensions | |||
| Unladen weight declared | 4,674 lb · 2,120 kg | 5,975 lb · 2,710 kg | +28% 205/205-4 |
| Wheelbase declared | 77.0 in · 1,955 mm | 83.1 in · 2,112 mm | +8% 205/205-4 |
| Length declared | 135.8 in · 3,450 mm | 146.1 in · 3,710 mm | +8% 205/205-4 |
| Width declared | 64.2 in · 1,630 mm | 76.8–97.2 in · 1,950–2,470 mm | differs |
| Ground clearance declared | 15.4 in · 390 mm | 17.3 in · 440 mm | +13% 205/205-4 |
| Turning radius, braked declared | 11.4 ft · 3.46 m | 11.8 ft · 3.60 m | — |
| Fuel tank declared | 65.5 qt · 62.0 L | 77.1 qt · 73.0 L | +18% 205/205-4 |
Height is not in this table. It is not one measurement: the sources measure it to different points — over the cab on some machines, over the steering wheel or the exhaust on others — and the same tractor measured two ways can differ by most of a metre. It appears here only when both machines' figures carry the point they were measured to and it is the same point, which is not the case for these two. Each machine's own page prints its height as its source gives it.
Landini 5860 (DT) TL 38 N/M (TL-38 DT/M) sources
- Source: Traktorenlexikon, “Landini R 5560 L (DT)”
- Source: Traktorenlexikon, “Lindner BF 420 SN/SA”
VALMET 205/205-4 sources
- Source: Traktorenlexikon, “Valmet 205”