Landini 5860 (DT) TL 38 N/M (TL-38 DT/M) or VALMET 205/205-4?
Which should you choose?
The data can’t decide this. Power at the PTO shaft cannot be compared: the 5860 (DT) TL 38 N/M (TL-38 DT/M) has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 205/205-4 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- The VALMET 205/205-4 suits loader and hydraulic implement work better on this data: 19% (400 kg / 882 lb) more three-point lift.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | 5860 (DT) TL 38 N/M (TL-38 DT/M) | 205/205-4 | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 35.3 kW (47.3 hp)Traktorenlexikon, “Landini R 5560 L (DT)” | 36 kW (48 hp)Traktorenlexikon, “Valmet 205” | Not comparableNot comparable on power at the PTO shaft: the 5860 (DT) TL 38 N/M (TL-38 DT/M) has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 205/205-4 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the 5860 (DT) TL 38 N/M (TL-38 DT/M) and the 205/205-4. |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the 5860 (DT) TL 38 N/M (TL-38 DT/M) and the 205/205-4. |
| Which pumps more oil for implements? | — | 39.0 L/min (10.3 gpm)Traktorenlexikon, “Valmet 205” | No figureNo call on hydraulic flow: no figure on record for the 5860 (DT) TL 38 N/M (TL-38 DT/M). |
| Which lifts more on the three-point hitch? | 2,100 kg (4,630 lb)Traktorenlexikon, “Landini R 5560 L (DT)” | 2,500 kg (5,512 lb)Traktorenlexikon, “Valmet 205” | AheadThe VALMET 205/205-4 has 19% more lift (400 kg / 882 lb) than the Landini 5860 (DT) TL 38 N/M (TL-38 DT/M) (both lift at the hitch ends, as stated by the source). |
| Which is heavier, for traction? | 2,120 kg (4,674 lb)Traktorenlexikon, “Landini R 5560 L (DT)” | 2,710 kg (5,975 lb)Traktorenlexikon, “Valmet 205” | Ahead (a fact, not an advantage)The VALMET 205/205-4 is 28% heavier (590 kg / 1,301 lb) than the Landini 5860 (DT) TL 38 N/M (TL-38 DT/M) (both unladen weight, as stated by the source). |
| Which may carry more ballast and load? | — | — | No figureNo call on maximum permissible mass: no figure on record for the 5860 (DT) TL 38 N/M (TL-38 DT/M) and the 205/205-4. |
| Which has the wider choice of gears? | 12 to 24Traktorenlexikon, “Landini R 5560 L (DT)” | 8Traktorenlexikon, “Valmet 205” | AheadThe Landini 5860 (DT) TL 38 N/M (TL-38 DT/M) has 50% more forward gears (4 gears) than the VALMET 205/205-4 (both forward gears, as stated by the source). |
| Which offers a creeper range? | — | — | No figureNo call on a creeper range: not stated for the 5860 (DT) TL 38 N/M (TL-38 DT/M) and the 205/205-4. |
| Which is faster on the road? | 30 km/h (18.6 mph)Traktorenlexikon, “Landini R 5560 L (DT)” | 30 km/h (18.6 mph)Traktorenlexikon, “Valmet 205” | EvenEven on top speed (both top speed forward, as stated by the source): the difference is under the 10% threshold, too small to call. |
| Which offers more PTO speeds? | 540 rpm / 1000 rpmTraktorenlexikon, “Landini R 5560 L (DT)” | 540 rpmTraktorenlexikon, “Valmet 205” | AheadThe Landini 5860 (DT) TL 38 N/M (TL-38 DT/M) offers 1000 rpm at the PTO, which the VALMET 205/205-4 does not (as stated by the sources). |
| Which PTO runs independently of the ground drive? | — | independentTraktorenlexikon, “Valmet 205” | No figureNo call on PTO independence: not stated for the 5860 (DT) TL 38 N/M (TL-38 DT/M). |
| Which drives on both axles? | Two-wheel or four-wheel driveTraktorenlexikon, “Landini R 5560 L (DT)” | Two-wheel or four-wheel driveTraktorenlexikon, “Valmet 205” | EvenEven on drive: every machine is available with four-wheel drive. |
| Which is newer, and what about parts? | 1988–2000 | 1989–1991 | EvenSame era: production began within 5 years of each other. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The VALMET 205/205-4 has 19% more lift (400 kg / 882 lb) than the Landini 5860 (DT) TL 38 N/M (TL-38 DT/M) (both lift at the hitch ends, as stated by the source).
- The VALMET 205/205-4 is 28% heavier (590 kg / 1,301 lb) than the Landini 5860 (DT) TL 38 N/M (TL-38 DT/M) (both unladen weight, as stated by the source).
- The Landini 5860 (DT) TL 38 N/M (TL-38 DT/M) has 50% more forward gears (4 gears) than the VALMET 205/205-4 (both forward gears, as stated by the source).
- The Landini 5860 (DT) TL 38 N/M (TL-38 DT/M) offers 1000 rpm at the PTO, which the VALMET 205/205-4 does not (as stated by the sources).
- Even on top speed (both top speed forward, as stated by the source): the difference is under the 10% threshold, too small to call.
- Even on drive: every machine is available with four-wheel drive.
- Same era: production began within 5 years of each other. We hold no parts-availability data, so there is no call on parts.
- Not comparable on power at the PTO shaft: the 5860 (DT) TL 38 N/M (TL-38 DT/M) has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 205/205-4 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, hydraulic flow, maximum permissible mass, a creeper range and PTO independence.
← Every figure for both machines, side by side, with sources