8 material differences · fewer than 12
Tractor oneLandini 7830 (DT) TL-20 N/F (TL-20 DT/F)1983–1987No measured PTO figureTractor twoZETOR 7711/77451985–1993No measured PTO figure
Which should you choose?
Read our verdict on the 7830 (DT) TL-20 N/F (TL-20 DT/F) and the 7711/7745 → It is generated from the rows below by a fixed, versioned rule set, and names the figure behind every call.
Field by field
8 material differences · 6 fields identical or within 5%, which is not counted as material
| Field | 7830 (DT) TL-20 N/F (TL-20 DT/F) | 7711/7745 | Gap |
|---|---|---|---|
| Engine | |||
| Engine power, claimed claimed | 71 hp | 72.0 hp | — |
| Engine declared | Perkins A 4.236 | ZBROJORKA Z-7701 | differs |
| Displacement declared | 3.87 L | 3.92 L | — |
| Maximum torque declared | 202 lb·ft · 274 N·m | 182 lb·ft · 247 N·m | +11% 7830 (DT) TL-20 N/F (TL-20 DT/F) |
| Transmission | |||
| Top speed declared | 18.6 mph · 30 km/h | 15.5 mph · 25 km/h | +20% 7830 (DT) TL-20 N/F (TL-20 DT/F) |
| Hydraulics & hitch | |||
| Pump flow declared | 10.2 gpm · 38.7 L/min | 9.7 gpm · 36.9 L/min | — |
| Rear PTO speeds declared | 540/1000 rpm | 540/1000 rpm | — |
| Weight & dimensions | |||
| Unladen weight declared | 5,986 lb · 2,715 kg | 6,841 lb · 3,103 kg | +14% 7711/7745 |
| Wheelbase declared | 87.0 in · 2,210 mm | 88.9 in · 2,257 mm | — |
| Length declared | 147.6 in · 3,750 mm | 148.0 in · 3,760 mm | — |
| Width declared | 78.7 in · 1,999 mm | 72.4–87.8 in · 1,840–2,230 mm | differs |
| Ground clearance declared | 21.1 in · 535 mm | 19.3 in · 490 mm | +9% 7830 (DT) TL-20 N/F (TL-20 DT/F) |
| Turning radius, braked declared | 12.8 ft · 3.89 m | 11.5 ft · 3.51 m | +11% 7830 (DT) TL-20 N/F (TL-20 DT/F) |
| Fuel tank declared | 63.9 qt · 60.5 L | 74.0 qt · 70.0 L | +16% 7711/7745 |
Height is not in this table. It is not one measurement: the sources measure it to different points — over the cab on some machines, over the steering wheel or the exhaust on others — and the same tractor measured two ways can differ by most of a metre. It appears here only when both machines' figures carry the point they were measured to and it is the same point, which is not the case for these two. Each machine's own page prints its height as its source gives it.
Landini 7830 (DT) TL-20 N/F (TL-20 DT/F) sources
- Source: Traktorenlexikon, “Landini 7830 (DT)”
- Source: Traktorenlexikon, “Massey Ferguson MF 168 & MF 168A”
ZETOR 7711/7745 sources
- Source: Traktorenlexikon, “Zetor 7711”