10 material differences · fewer than 12
Tractor oneLandini R-7500 (DT) "TL 20 N/B"1973–1983No measured PTO figureTractor twoVALMET 605/605-41983–1989No measured PTO figure
Which should you choose?
Read our verdict on the R-7500 (DT) "TL 20 N/B" and the 605/605-4 → It is generated from the rows below by a fixed, versioned rule set, and names the figure behind every call.
Field by field
10 material differences · 3 fields identical or within 5%, which is not counted as material
| Field | R-7500 (DT) "TL 20 N/B" | 605/605-4 | Gap |
|---|---|---|---|
| Engine | |||
| Engine power, claimed claimed | 71 hp | 71.1 hp | — |
| Engine declared | Perkins A 4.236 | VALMET TD 33 DS 6 | differs |
| Displacement declared | 3.87 L | 3.30 L | +17% R-7500 (DT) "TL 20 N/B" |
| Maximum torque declared | 196 lb·ft · 266 N·m | — | — |
| Transmission | |||
| Top speed declared | 18.6 mph · 30 km/h | 18.6 mph · 30 km/h | — |
| Clutch declared | Dry LUK double clutch | Pedal operated dry LuK single-disc clutch | differs |
| Hydraulics & hitch | |||
| Pump flow declared | 7.4 gpm · 28.0 L/min | 13.9 gpm · 52.7 L/min | +88% 605/605-4 |
| Rear PTO speeds declared | 540 rpm / 1000 rpm | 540/1000 rpm | differs |
| Weight & dimensions | |||
| Unladen weight declared | 5,181 lb · 2,350 kg | 7,584 lb · 3,440 kg | +46% 605/605-4 |
| Wheelbase declared | 88.2 in · 2,240 mm | 93.2 in · 2,368 mm | +6% 605/605-4 |
| Length declared | 142.5 in · 3,620 mm | 168.9 in · 4,290 mm | +19% 605/605-4 |
| Width declared | 71.7–91.7 in · 1,820–2,330 mm | 80.3–99.6 in · 2,040–2,530 mm | differs |
| Ground clearance declared | 17.3 in · 440 mm | 17.1 in · 435 mm | — |
| Turning radius, braked declared | 11.2 ft · 3.42 m | — | — |
| Fuel tank declared | 64.5 qt · 61.0 L | 190.2 qt · 180.0 L | +195% 605/605-4 |
Height is not in this table. It is not one measurement: the sources measure it to different points — over the cab on some machines, over the steering wheel or the exhaust on others — and the same tractor measured two ways can differ by most of a metre. It appears here only when both machines' figures carry the point they were measured to and it is the same point, which is not the case for these two. Each machine's own page prints its height as its source gives it.
Landini R-7500 (DT) "TL 20 N/B" sources
- Source: Traktorenlexikon, “Landini 7500”
- Source: Traktorenlexikon, “Massey Ferguson MF 168 & MF 168A”
VALMET 605/605-4 sources
- Source: Traktorenlexikon, “Valmet 605”