11 material differences · fewer than 12
Tractor oneLandini 5830 (DT) TL-22 N/G (TL-DT/L)1983–1987No measured PTO figureTractor twoVALMET 5041982–1985No measured PTO figure
Which should you choose?
Read our verdict on the 5830 (DT) TL-22 N/G (TL-DT/L) and the 504 → It is generated from the rows below by a fixed, versioned rule set, and names the figure behind every call.
Field by field
11 material differences · 4 fields identical or within 5%, which is not counted as material
| Field | 5830 (DT) TL-22 N/G (TL-DT/L) | 504 | Gap |
|---|---|---|---|
| Engine | |||
| Engine power, claimed claimed | 49.3 hp | 49.3 hp | — |
| Engine declared | Perkins AD 3.152 S | VALMET D 27 B | differs |
| Displacement declared | 2.50 L | 2.69 L | +7% 504 |
| Maximum torque declared | 133 lb·ft · 181 N·m | 125 lb·ft · 170 N·m | +6% 5830 (DT) TL-22 N/G (TL-DT/L) |
| Transmission | |||
| Top speed declared | 18.6 mph · 30 km/h | 18.6 mph · 30 km/h | — |
| Clutch declared | Dry, air-cooled OMG double clutch | dry Fichtel & Sachs dual clutch | differs |
| Hydraulics & hitch | |||
| Pump flow declared | 9.5 gpm · 36.1 L/min | 7.1 gpm · 27.0 L/min | +34% 5830 (DT) TL-22 N/G (TL-DT/L) |
| Rear PTO speeds declared | 540/1000 rpm | 540 rpm | differs |
| Weight & dimensions | |||
| Unladen weight declared | 4,674 lb · 2,120 kg | 5,930 lb · 2,690 kg | +27% 504 |
| Wheelbase declared | 81.9 in · 2,080 mm | 83.1 in · 2,112 mm | — |
| Length declared | 140.7 in · 3,575 mm | 142.4 in · 3,617 mm | — |
| Width declared | 69.1 in · 1,755 mm | 74.4 in · 1,890 mm | +8% 504 |
| Ground clearance declared | 17.1 in · 435 mm | 15.7 in · 400 mm | +9% 5830 (DT) TL-22 N/G (TL-DT/L) |
| Turning radius, braked declared | 12.4 ft · 3.79 m | 11.5 ft · 3.50 m | +8% 5830 (DT) TL-22 N/G (TL-DT/L) |
| Fuel tank declared | 63.9 qt · 60.5 L | 68.7 qt · 65.0 L | +7% 504 |
Height is not in this table. It is not one measurement: the sources measure it to different points — over the cab on some machines, over the steering wheel or the exhaust on others — and the same tractor measured two ways can differ by most of a metre. It appears here only when both machines' figures carry the point they were measured to and it is the same point, which is not the case for these two. Each machine's own page prints its height as its source gives it.
Landini 5830 (DT) TL-22 N/G (TL-DT/L) sources
- Source: Traktorenlexikon, “Landini 5830 (DT)”
- Source: Traktorenlexikon, “Massey Ferguson MF 255”
VALMET 504 sources
- Source: Traktorenlexikon, “Valmet 504”