10 material differences · fewer than 12
Tractor oneJohn Deere-LANZ 7101965–1967No measured PTO figureTractor twoLandini R-5500 (DT) "TL 22 N/A"1973–1983No measured PTO figure
Which should you choose?
Read our verdict on the 710 and the R-5500 (DT) "TL 22 N/A" → It is generated from the rows below by a fixed, versioned rule set, and names the figure behind every call.
Field by field
10 material differences · 4 fields identical or within 5%, which is not counted as material
| Field | 710 | R-5500 (DT) "TL 22 N/A" | Gap |
|---|---|---|---|
| Engine | |||
| Engine power, claimed claimed | 49.3 hp | 49.3 hp | — |
| Engine declared | John Deere 202 D 23 L | Perkins AD 3.152 S | differs |
| Displacement declared | 3.32 L | 2.50 L | +33% 710 |
| Maximum torque declared | 132 lb·ft · 178 N·m | 128 lb·ft · 173 N·m | — |
| Transmission | |||
| Top speed declared | 12.4–15.5 mph · 20–25 km/h | 15.5 mph · 25 km/h | differs |
| Hydraulics & hitch | |||
| Pump flow declared | 4.1 gpm · 15.6 L/min | 7.6 gpm · 28.6 L/min | +83% R-5500 (DT) "TL 22 N/A" |
| Pressure declared | 2,162 psi · 149 bar | — | — |
| Rear PTO speeds declared | 540/1000 rpm | 540/1000 rpm | — |
| Weight & dimensions | |||
| Unladen weight declared | 4,925 lb · 2,234 kg | 4,431 lb · 2,010 kg | +11% 710 |
| Maximum permissible mass declared | 7,716 lb · 3,500 kg | — | — |
| Wheelbase declared | 86.6 in · 2,200 mm | 81.9 in · 2,080 mm | +6% 710 |
| Length declared | 139.0 in · 3,530 mm | 138.6 in · 3,520 mm | — |
| Width declared | 70.5 in · 1,790 mm | 69.3–89.0 in · 1,760–2,260 mm | differs |
| Ground clearance declared | 19.7 in · 500 mm | 16.5 in · 420 mm | +19% 710 |
| Turning radius, braked declared | 10.2 ft · 3.10 m | 10.9 ft · 3.31 m | +7% R-5500 (DT) "TL 22 N/A" |
| Fuel tank declared | 74.0 qt · 70.0 L | 64.5 qt · 61.0 L | +15% 710 |
Height is not in this table. It is not one measurement: the sources measure it to different points — over the cab on some machines, over the steering wheel or the exhaust on others — and the same tractor measured two ways can differ by most of a metre. It appears here only when both machines' figures carry the point they were measured to and it is the same point, which is not the case for these two. Each machine's own page prints its height as its source gives it.
John Deere-LANZ 710 sources
- Source: Traktorenlexikon, “John Deere-Lanz 710”
Landini R-5500 (DT) "TL 22 N/A" sources
- Source: Traktorenlexikon, “Landini 5500”
- Source: Traktorenlexikon, “Massey Ferguson MF 255”