John Deere 5103 vs VALMET 365 (365-4)
14 material differences
Which should you choose?
We will not advise between these two machines, because their power is not stated as the same quantity on both; their unladen weight differs by more than 25% (34%); they were not built in overlapping years (2003–2008; 1994–1997). The figures below are side by side so you can judge them yourself; each says whether it was measured, claimed or declared by its source.
Field by field
14 material differences · 3 fields identical or within 5%, which is not counted as material
| Field | 5103 | 365 (365-4) | Gap |
|---|---|---|---|
| Measured performance | |||
| PTO power, measured measured | 49.8 hp | — | — |
| Drawbar power, measured measured | 40.9 hp | — | — |
| Engine | |||
| Engine power, claimed claimed | — | 60.2 hp | — |
| Engine declared | John Deere 3.029 DPY-12 | VALMET 320 D | differs |
| Displacement declared | 2.90 L | 3.30 L | +14% 365 (365-4) |
| Maximum torque declared | 129 lb·ft · 175.2 N·m | 162 lb·ft · 220 N·m | +26% 365 (365-4) |
| Transmission | |||
| Top speed declared | 18.6 mph · 30 km/h | 18.6–24.9 mph · 30–40 km/h | differs |
| Clutch declared | Dry LuK double clutch with 280 mm diameter | Dry FICHTEL & SACHS double clutch | differs |
| Hydraulics & hitch | |||
| Hydraulic centre declared | Open centre | Open centre | — |
| Pump flow declared | 11.3 gpm · 42.8 L/min | 14.5 gpm · 55.0 L/min | +29% 365 (365-4) |
| Pressure declared | 2,828 psi · 195 bar | 2,901 psi · 200 bar | — |
| Three-point lift at ends declared | 3,726 lb · 1,690 kg | 5,688 lb · 2,580 kg | +53% 365 (365-4) |
| Rear PTO speeds declared | 540/1000 rpm | 540E/540 rpm | differs |
| Weight & dimensions | |||
| Unladen weight declared | 4,652–5,031 lb · 2,110–2,282 kg | 6,217 lb · 2,820 kg | differs |
| Wheelbase declared | 81.1 in · 2,060 mm | 83.1 in · 2,112 mm | — |
| Length declared | 137.4 in · 3,490 mm | 146.1 in · 3,710 mm | +6% 365 (365-4) |
| Width declared | 65.7 in · 1,670 mm | 79.9 in · 2,030 mm | +22% 365 (365-4) |
| Height declared | 93.7 in · 2,380 mm | 103.5 in · 2,630 mm | +11% 365 (365-4) |
| Ground clearance declared | 12.2 in · 310 mm | 15.9 in · 405 mm | +31% 365 (365-4) |
| Turning radius, braked declared | — | 11.5 ft · 3.50 m | — |
| Fuel tank declared | 72.0 qt · 68.1 L | 77.1 qt · 73.0 L | +7% 365 (365-4) |
John Deere 5103 sources
Source
- Source: OECD test report 2266, 2005
- Source: Traktorenlexikon, “John Deere 5103”
VALMET 365 (365-4) sources
Source
- Source: Traktorenlexikon, “Valmet 365”
- Source: Traktorenlexikon, “Valmet 255”