10 material differences · fewer than 12
Tractor oneHürlimann XN-7061998–2003No measured PTO figureTractor twoLandini TL 32 A (DT) "R 6530 F"1983–1987No measured PTO figure
Which should you choose?
Read our verdict on the XN-706 and the TL 32 A (DT) "R 6530 F" → It is generated from the rows below by a fixed, versioned rule set, and names the figure behind every call.
Field by field
10 material differences · 3 fields identical or within 5%, which is not counted as material
| Field | XN-706 | TL 32 A (DT) "R 6530 F" | Gap |
|---|---|---|---|
| Engine | |||
| Engine power, claimed claimed | 59.3 hp | 63.2 hp | +7% TL 32 A (DT) "R 6530 F" |
| Engine declared | Hürlimann 1000.3 W-1 | Perkins A 4.236 | differs |
| Displacement declared | 3.00 L | 3.87 L | +29% TL 32 A (DT) "R 6530 F" |
| Maximum torque declared | 120 lb·ft · 163 N·m | 176 lb·ft · 239 N·m | +47% TL 32 A (DT) "R 6530 F" |
| Transmission | |||
| Top speed declared | 18.6 mph · 30 km/h | 18.6 mph · 30 km/h | — |
| Clutch declared | Pedal-operated dry SDF single-plate clutch | — | — |
| Hydraulics & hitch | |||
| Pump flow declared | 9.0 gpm · 34.0 L/min | 9.8 gpm · 37.1 L/min | +9% TL 32 A (DT) "R 6530 F" |
| Pressure declared | 3,046 psi · 210 bar | — | — |
| Rear PTO speeds declared | 540 rpm / 1000 rpm | 540/1000 rpm | differs |
| Weight & dimensions | |||
| Unladen weight declared | 5,181 lb · 2,350 kg | 4,497 lb · 2,040 kg | +15% XN-706 |
| Wheelbase declared | 75.8 in · 1,926 mm | 81.5 in · 2,071 mm | +8% TL 32 A (DT) "R 6530 F" |
| Length declared | 135.1 in · 3,431 mm | 137.0 in · 3,480 mm | — |
| Width declared | 50.8–64.6 in · 1,290–1,640 mm | 53.5–75.0 in · 1,358–1,904 mm | differs |
| Ground clearance declared | 9.1 in · 230 mm | 13.9 in · 353 mm | +53% TL 32 A (DT) "R 6530 F" |
| Turning radius, braked declared | 11.2 ft · 3.40 m | 11.1 ft · 3.38 m | — |
| Fuel tank declared | 61.3 qt · 58.0 L | 56.0 qt · 53.0 L | +9% XN-706 |
Height is not in this table. It is not one measurement: the sources measure it to different points — over the cab on some machines, over the steering wheel or the exhaust on others — and the same tractor measured two ways can differ by most of a metre. It appears here only when both machines' figures carry the point they were measured to and it is the same point, which is not the case for these two. Each machine's own page prints its height as its source gives it.
Hürlimann XN-706 sources
- Source: Traktorenlexikon, “Hürlimann XN 706”
- Source: Traktorenlexikon, “Hürlimann XA 606”
Landini TL 32 A (DT) "R 6530 F" sources
- Source: Traktorenlexikon, “Landini TL 32 (DT)”
- Source: Traktorenlexikon, “Massey Ferguson MF 168 & MF 168A”