10 material differences · fewer than 12
Tractor oneGüldner G 751965–1969No measured PTO figureTractor twoInternational Harvester 824 (A)1971–1974No measured PTO figure
Which should you choose?
We will not advise between these two machines, because they were not built in overlapping years (1965–1969; 1971–1974). The figures below are side by side so you can judge them yourself; each says whether it was measured, claimed or declared by its source.
Field by field
10 material differences · 3 fields identical or within 5%, which is not counted as material
| Field | G 75 | 824 (A) | Gap |
|---|---|---|---|
| Engine | |||
| Engine power, claimed claimed | — | 73.0 hp | — |
| Engine declared | Güldner 6 L 79 | INTERNATIONAL-HARVESTER D-239 or D-246 | differs |
| Displacement declared | 4.71 L | — | — |
| Maximum torque declared | 174 lb·ft · 235 N·m | 185 lb·ft · 251 N·m | +7% 824 (A) |
| Transmission | |||
| Top speed declared | 15.0 mph · 24.1 km/h | 18.6 mph · 30 km/h | +24% 824 (A) |
| Clutch declared | Pedal-operated dry double clutch | Pedal-operated dry LuK single-disc clutch | differs |
| Hydraulics & hitch | |||
| Pump flow declared | — | 7.7 gpm · 29.2 L/min | — |
| Pressure declared | 2,134 psi · 147 bar | 2,988 psi · 206 bar | +40% 824 (A) |
| Rear PTO speeds declared | 540/1000 rpm | 540/1000 rpm | — |
| Weight & dimensions | |||
| Unladen weight declared | 6,724 lb · 3,050 kg | 6,934 lb · 3,145 kg | — |
| Maximum permissible mass declared | 11,023 lb · 5,000 kg | — | — |
| Wheelbase declared | 95.1 in · 2,416 mm | 83.5 in · 2,120 mm | +14% G 75 |
| Length declared | 159.4–165.4 in · 4,050–4,200 mm | 131.4 in · 3,337 mm | differs |
| Width declared | 76.6 in · 1,945 mm | 78.3 in · 1,990 mm | — |
| Ground clearance declared | 15.7 in · 400 mm | 17.8 in · 453 mm | +13% 824 (A) |
| Turning radius, braked declared | 11.7 ft · 3.58 m | 12.5 ft · 3.80 m | +6% 824 (A) |
| Fuel tank declared | 68.7 qt · 65 L | 74.0 qt · 70.0 L | +8% 824 (A) |
Height is not in this table. It is not one measurement: the sources measure it to different points — over the cab on some machines, over the steering wheel or the exhaust on others — and the same tractor measured two ways can differ by most of a metre. It appears here only when both machines' figures carry the point they were measured to and it is the same point, which is not the case for these two. Each machine's own page prints its height as its source gives it.
Güldner G 75 sources
- Source: Traktorenlexikon, “Güldner G 75”
- Source: Traktorenlexikon, “Güldner G 75A”
International Harvester 824 (A) sources
- Source: Traktorenlexikon, “McCormick 824 (A)”