13 material differences

Tractor oneFord 4830 (A)1990–1992No measured PTO figureTractor twoLandini 6560 L (DT) TL 37 N/M (TL-37 DT/M)1988–2000No measured PTO figure

Which should you choose?

Read our verdict on the 4830 (A) and the 6560 L (DT) TL 37 N/M (TL-37 DT/M) → It is generated from the rows below by a fixed, versioned rule set, and names the figure behind every call.

Field by field

13 material differences · 3 fields identical or within 5%, which is not counted as material

Ford 4830 (A) and Landini 6560 L (DT) TL 37 N/M (TL-37 DT/M), field by field
Field4830 (A)6560 L (DT) TL 37 N/M (TL-37 DT/M)Gap
Engine
Engine power, claimed claimed64.1 hp64.1 hp—
Engine declaredFord L 256 CID-NAPerkins A 4.236differs
Displacement declared4.19 L3.87 L+8% 4830 (A)
Maximum torque declared184 lb·ft · 250 N·m181 lb·ft · 245 N·m—
Transmission
Top speed declared18.6–24.9 mph · 30–40 km/h18.6 mph · 30 km/hdiffers
Clutch declaredPedal-operated dry AP single-disc clutchDry and air-cooled OMG double clutchdiffers
Hydraulics & hitch
Hydraulic centre declaredOpen centre——
Pump flow declared9.3 gpm · 35.3 L/min11.2 gpm · 42.3 L/min+20% 6560 L (DT) TL 37 N/M (TL-37 DT/M)
Pressure declared1,378–1,450 psi · 95–100 bar2,756 psi · 190 bardiffers
Three-point lift, at the coupling points declared4,381 lb · 1,987 kg4,630 lb · 2,100 kg+6% 6560 L (DT) TL 37 N/M (TL-37 DT/M)
Rear PTO speeds declared540 rpm540 rpm / 1000 rpmdiffers
Weight & dimensions
Unladen weight declared6,526 lb · 2,960 kg5,004 lb · 2,270 kg+30% 4830 (A)
Wheelbase declared89.6 in · 2,276 mm81.5 in · 2,070 mm+10% 4830 (A)
Length declared143.7 in · 3,650 mm140.6 in · 3,570 mm—
Width declared69.7–96.7 in · 1,771–2,457 mm65.7–87.4 in · 1,670–2,220 mmdiffers
Ground clearance declared12.0 in · 305 mm16.5 in · 420 mm+38% 6560 L (DT) TL 37 N/M (TL-37 DT/M)
Turning radius, braked declared—10.8 ft · 3.29 m—
Fuel tank declared69.4 qt · 65.7 L65.5 qt · 62.0 L+6% 4830 (A)

Height is not in this table. It is not one measurement: the sources measure it to different points — over the cab on some machines, over the steering wheel or the exhaust on others — and the same tractor measured two ways can differ by most of a metre. It appears here only when both machines' figures carry the point they were measured to and it is the same point, which is not the case for these two. Each machine's own page prints its height as its source gives it.

Ford 4830 (A) sources

Source
  • Source: Traktorenlexikon, “Ford 4830”

Landini 6560 L (DT) TL 37 N/M (TL-37 DT/M) sources

Source
  • Source: Traktorenlexikon, “Landini R 6560 L (DT)”
  • Source: Traktorenlexikon, “Massey Ferguson MF 168 & MF 168A”