9 material differences · fewer than 12
Tractor oneDeutz-Fahr DX 6.051987–1991No measured PTO figureTractor twoMassey Ferguson MF 399 (A)1987–1997No measured PTO figure
Which should you choose?
Read our verdict on the DX 6.05 and the MF 399 (A) → It is generated from the rows below by a fixed, versioned rule set, and names the figure behind every call.
Field by field
9 material differences · 5 fields identical or within 5%, which is not counted as material
| Field | DX 6.05 | MF 399 (A) | Gap |
|---|---|---|---|
| Engine | |||
| Engine power, claimed claimed | 97 hp | 95.7 hp | — |
| Engine declared | KHD F6L 912 | Perkins A 6.354-4 | differs |
| Displacement declared | 5.65 L | 5.80 L | — |
| Maximum torque declared | 266 lb·ft · 360 N·m | — | — |
| Transmission | |||
| Top speed declared | 18.6–24.9 mph · 30–40 km/h | 18.6–24.9 mph · 30–40 km/h | — |
| Clutch declared | Independent dry double clutch | Pedal operated, dry and air-cooled LuK single clutch | differs |
| Hydraulics & hitch | |||
| Hydraulic centre declared | Open centre | — | — |
| Pump flow declared | 12.9 gpm · 48.8 L/min | 16.7 gpm · 63.3 L/min | +30% MF 399 (A) |
| Pressure declared | 3,481 psi · 240 bar | 2,973–3,481 psi · 205–240 bar | differs |
| Three-point lift, at the coupling points declared | 11,464 lb · 5,200 kg | 7,937 lb · 3,600 kg | +44% DX 6.05 |
| Rear PTO speeds declared | 540/1000 rpm | 540 rpm / 1000 rpm | differs |
| Weight & dimensions | |||
| Unladen weight declared | 9,987 lb · 4,530 kg | 7,840 lb · 3,556 kg | +27% DX 6.05 |
| Maximum permissible mass declared | 14,991 lb · 6,800 kg | — | — |
| Wheelbase declared | 105.0 in · 2,667 mm | 101.4 in · 2,576 mm | — |
| Length declared | 175.7 in · 4,464 mm | 168.5 in · 4,280 mm | — |
| Width declared | 87.0 in · 2,210 mm | 77.6 in · 1,970 mm | +12% DX 6.05 |
| Ground clearance declared | 17.9 in · 455 mm | 14.2 in · 360 mm | +26% DX 6.05 |
| Turning radius, braked declared | 16.0 ft · 4.87 m | — | — |
| Fuel tank declared | 137.4 qt · 130 L | — | — |
Height is not in this table. It is not one measurement: the sources measure it to different points — over the cab on some machines, over the steering wheel or the exhaust on others — and the same tractor measured two ways can differ by most of a metre. It appears here only when both machines' figures carry the point they were measured to and it is the same point, which is not the case for these two. Each machine's own page prints its height as its source gives it.
Deutz-Fahr DX 6.05 sources
- Source: Traktorenlexikon, “Deutz-Fahr DX 6.05”
- Source: Traktorenlexikon, “Deutz-Fahr DX 110”
Massey Ferguson MF 399 (A) sources
- Source: Traktorenlexikon, “Massey Ferguson MF 399”