10 material differences · fewer than 12
Tractor oneDeutz-Fahr DX 4.101985–1988No measured PTO figureTractor twoFiat 70-66 F (DT/F)1984–1991No measured PTO figure
Which should you choose?
Read our verdict on the DX 4.10 and the 70-66 F (DT/F) → It is generated from the rows below by a fixed, versioned rule set, and names the figure behind every call.
Field by field
10 material differences · 4 fields identical or within 5%, which is not counted as material
| Field | DX 4.10 | 70-66 F (DT/F) | Gap |
|---|---|---|---|
| Engine | |||
| Engine power, claimed claimed | 69.1 hp | 69.1 hp | — |
| Engine declared | KHD F4L 912 | FIAT-IVECO 8045.06.206 or 306 | differs |
| Displacement declared | 3.77 L | 3.61 L | — |
| Maximum torque declared | 175 lb·ft · 237 N·m | 165 lb·ft · 224 N·m | +6% DX 4.10 |
| Transmission | |||
| Top speed declared | 18.6–24.9 mph · 30–40 km/h | 18.6 mph · 30 km/h | differs |
| Clutch declared | — | Dry Valeo or LuK double clutch | — |
| Hydraulics & hitch | |||
| Pump flow declared | 10.6 gpm · 40.0 L/min | 8.7 gpm · 32.8 L/min | +22% DX 4.10 |
| Pressure declared | 3,481 psi · 240 bar | 3,046 psi · 210 bar | +14% DX 4.10 |
| Rear PTO speeds declared | 540/1000 rpm | 540/1000 rpm | — |
| Weight & dimensions | |||
| Unladen weight declared | 8,642 lb · 3,920 kg | 4,277 lb · 1,940 kg | +102% DX 4.10 |
| Wheelbase declared | 94.5 in · 2,400 mm | 78.8 in · 2,001 mm | +20% DX 4.10 |
| Length declared | 163.0 in · 4,140 mm | 121.7 in · 3,090 mm | +34% DX 4.10 |
| Width declared | 90.6 in · 2,300 mm | 65.7 in · 1,670 mm | +38% DX 4.10 |
| Ground clearance declared | 16.7 in · 425 mm | 17.1 in · 435 mm | — |
| Turning radius, braked declared | 13.7 ft · 4.17 m | — | — |
| Fuel tank declared | 132.1 qt · 125 L | 52.8 qt · 50.0 L | +150% DX 4.10 |
Height is not in this table. It is not one measurement: the sources measure it to different points — over the cab on some machines, over the steering wheel or the exhaust on others — and the same tractor measured two ways can differ by most of a metre. It appears here only when both machines' figures carry the point they were measured to and it is the same point, which is not the case for these two. Each machine's own page prints its height as its source gives it.
Deutz-Fahr DX 4.10 sources
- Source: Traktorenlexikon, “Deutz-Fahr DX 4.10”
- Source: Traktorenlexikon, “Deutz D 6006”
Fiat 70-66 F (DT/F) sources
- Source: Traktorenlexikon, “Fiat 70-66 F/70-66 F/DT”
- Source: Traktorenlexikon, “Fiat 70-66/70-66 DT”