Deutz-Fahr DX 4.10 or Fiat 70-66 F (DT/F)?
Which should you choose?
The data can’t decide this. Power at the PTO shaft cannot be compared: the DX 4.10 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 70-66 F (DT/F) has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- The Deutz-Fahr DX 4.10 suits loader and hydraulic implement work better on this data: 22% (7.2 L/min / 1.9 gpm) more hydraulic flow.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | DX 4.10 | 70-66 F (DT/F) | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 51.5 kW (69.1 hp)Traktorenlexikon, “Deutz-Fahr DX 4.10” | 51.5 kW (69.1 hp)Traktorenlexikon, “Fiat 70-66 F/70-66 F/DT” | Not comparableNot comparable on power at the PTO shaft: the DX 4.10 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 70-66 F (DT/F) has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the DX 4.10 and the 70-66 F (DT/F). |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the DX 4.10 and the 70-66 F (DT/F). |
| Which pumps more oil for implements? | 40.0 L/min (10.6 gpm)Traktorenlexikon, “Deutz-Fahr DX 4.10” | 32.8 L/min (8.7 gpm)Traktorenlexikon, “Fiat 70-66 F/70-66 F/DT” | AheadThe Deutz-Fahr DX 4.10 has 22% more hydraulic flow (7.2 L/min / 1.9 gpm) than the Fiat 70-66 F (DT/F) (both pump flow, as stated by the source). |
| Which lifts more on the three-point hitch? | 3,800 kg (8,378 lb)Traktorenlexikon, “Deutz-Fahr DX 4.10” | 2,648 kg (5,838 lb)Traktorenlexikon, “Fiat 70-66 F/70-66 F/DT” | Not comparableNot comparable on three-point lift: the DX 4.10: lift at the hitch ends, as stated by the source (Traktorenlexikon, “Deutz-Fahr DX 4.10”); the 70-66 F (DT/F): lift 610 mm behind the hitch ends, as stated by the source (Traktorenlexikon, “Fiat 70-66 F/70-66 F/DT”) — not the same quantity, basis and condition. |
| Which is heavier, for traction? | 3,920 kg (8,642 lb)Traktorenlexikon, “Deutz-Fahr DX 4.10” | 1,940 kg (4,277 lb)Traktorenlexikon, “Fiat 70-66 F/70-66 F/DT” | Ahead (a fact, not an advantage)The Deutz-Fahr DX 4.10 is 102% heavier (1,980 kg / 4,365 lb) than the Fiat 70-66 F (DT/F) (both unladen weight, as stated by the source). |
| Which may carry more ballast and load? | — | — | No figureNo call on maximum permissible mass: no figure on record for the DX 4.10 and the 70-66 F (DT/F). |
| Which has the wider choice of gears? | 15 to 18Traktorenlexikon, “Deutz-Fahr DX 4.10” | 12 to 20Traktorenlexikon, “Fiat 70-66 F/70-66 F/DT” | EvenEven on forward gears (both forward gears, as stated by the source): the figures vary by configuration and the ranges overlap. |
| Which offers a creeper range? | — | — | No figureNo call on a creeper range: not stated for the DX 4.10 and the 70-66 F (DT/F). |
| Which is faster on the road? | 30 km/h (18.6 mph) to 40 km/h (24.9 mph)Traktorenlexikon, “Deutz-Fahr DX 4.10” | 30 km/h (18.6 mph)Traktorenlexikon, “Fiat 70-66 F/70-66 F/DT” | EvenEven on top speed (both top speed forward, as stated by the source): the figures vary by configuration and the ranges overlap. |
| Which offers more PTO speeds? | 540/1000 rpmTraktorenlexikon, “Deutz-Fahr DX 4.10” | 540/1000 rpmTraktorenlexikon, “Fiat 70-66 F/70-66 F/DT” | EvenEven on PTO speeds: the same speeds (540, 1000 rpm). |
| Which PTO runs independently of the ground drive? | independentTraktorenlexikon, “Deutz-Fahr DX 4.10” | independentTraktorenlexikon, “Fiat 70-66 F/70-66 F/DT” | EvenEven on PTO independence: every PTO is independent. |
| Which drives on both axles? | Two-wheel or four-wheel driveTraktorenlexikon, “Deutz-Fahr DX 4.10” | Two-wheel or four-wheel driveTraktorenlexikon, “Fiat 70-66 F/70-66 F/DT” | EvenEven on drive: every machine is available with four-wheel drive. |
| Which is newer, and what about parts? | 1985–1988 | 1984–1991 | EvenSame era: production began within 5 years of each other. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The Deutz-Fahr DX 4.10 has 22% more hydraulic flow (7.2 L/min / 1.9 gpm) than the Fiat 70-66 F (DT/F) (both pump flow, as stated by the source).
- The Deutz-Fahr DX 4.10 is 102% heavier (1,980 kg / 4,365 lb) than the Fiat 70-66 F (DT/F) (both unladen weight, as stated by the source).
- Even on forward gears (both forward gears, as stated by the source): the figures vary by configuration and the ranges overlap.
- Even on top speed (both top speed forward, as stated by the source): the figures vary by configuration and the ranges overlap.
- Even on PTO speeds: the same speeds (540, 1000 rpm).
- Even on PTO independence: every PTO is independent.
- Even on drive: every machine is available with four-wheel drive.
- Same era: production began within 5 years of each other. We hold no parts-availability data, so there is no call on parts.
- Not comparable on power at the PTO shaft: the DX 4.10 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 70-66 F (DT/F) has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- Not comparable on three-point lift: the DX 4.10: lift at the hitch ends, as stated by the source (Traktorenlexikon, “Deutz-Fahr DX 4.10”); the 70-66 F (DT/F): lift 610 mm behind the hitch ends, as stated by the source (Traktorenlexikon, “Fiat 70-66 F/70-66 F/DT”) — not the same quantity, basis and condition.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, maximum permissible mass and a creeper range.
← Every figure for both machines, side by side, with sources