10 material differences · fewer than 12
Tractor oneDeutz-Fahr DX 3.501984–1996No measured PTO figureTractor twoNew Holland 48351996–1998No measured PTO figure
Which should you choose?
Read our verdict on the DX 3.50 and the 4835 → It is generated from the rows below by a fixed, versioned rule set, and names the figure behind every call.
Field by field
10 material differences · 3 fields identical or within 5%, which is not counted as material
| Field | DX 3.50 | 4835 | Gap |
|---|---|---|---|
| Engine | |||
| Engine power, claimed claimed | 59 hp | 64 hp | +9% 4835 |
| Engine declared | KHD F3L 913 | Iveco 8045.06 R | differs |
| Displacement declared | 3.06 L | 3.61 L | +18% 4835 |
| Maximum torque declared | 144 lb·ft · 195 N·m | 146 lb·ft · 198 N·m | — |
| Transmission | |||
| Top speed declared | 18.6–24.9 mph · 30–40 km/h | 18.6–24.9 mph · 30–40 km/h | — |
| Clutch declared | Independent dry double clutch | Single-disc dry clutch | differs |
| Hydraulics & hitch | |||
| Hydraulic centre declared | — | Open centre | — |
| Hydraulic control declared | Constant flow | Constant flow | — |
| Pump flow declared | 10.0 gpm · 38.0 L/min | 12.2 gpm · 46.0 L/min | +21% 4835 |
| Rear PTO speeds declared | 540/1000 rpm | 540/540E/1000 rpm | differs |
| Weight & dimensions | |||
| Unladen weight declared | 6,019–6,878 lb · 2,730–3,120 kg | 7,209 lb · 3,270 kg | differs |
| Maximum permissible mass declared | 10,141 lb · 4,600 kg | — | — |
| Wheelbase declared | 79.2 in · 2,012 mm | 92.1 in · 2,340 mm | +16% 4835 |
| Length declared | 142.9 in · 3,630 mm | 156.7 in · 3,980 mm | +10% 4835 |
| Width declared | 84.2 in · 2,138 mm | 72.4 in · 1,840 mm | +16% DX 3.50 |
| Ground clearance declared | 18.0 in · 457 mm | 13.8 in · 350 mm | +31% DX 3.50 |
| Turning radius, braked declared | 11.8 ft · 3.60 m | — | — |
| Fuel tank declared | — | 116.2 qt · 110 L | — |
Height is not in this table. It is not one measurement: the sources measure it to different points — over the cab on some machines, over the steering wheel or the exhaust on others — and the same tractor measured two ways can differ by most of a metre. It appears here only when both machines' figures carry the point they were measured to and it is the same point, which is not the case for these two. Each machine's own page prints its height as its source gives it.
Deutz-Fahr DX 3.50 sources
- Source: Traktorenlexikon, “Deutz-Fahr DX 3.50”
- Source: Traktorenlexikon, “Fendt Farmer 260 S/SA”
New Holland 4835 sources
- Source: Traktorenlexikon, “New Holland 4835 (T)”
- Source: Traktorenlexikon, “New Holland 4835 Turbo”