11 material differences · fewer than 12
Tractor oneDeutz-Fahr DX 3.501984–1996No measured PTO figureTractor twoLeyland 3841969–1972No measured PTO figure
Which should you choose?
Read our verdict on the DX 3.50 and the 384 → It is generated from the rows below by a fixed, versioned rule set, and names the figure behind every call.
Field by field
11 material differences · 3 fields identical or within 5%, which is not counted as material
| Field | DX 3.50 | 384 | Gap |
|---|---|---|---|
| Engine | |||
| Engine power, claimed claimed | 59 hp | 70.0 hp | +19% 384 |
| Engine declared | KHD F3L 913 | LEYLAND-MOTORS 38 TD | differs |
| Displacement declared | 3.06 L | 3.77 L | +23% 384 |
| Maximum torque declared | 144 lb·ft · 195 N·m | 174 lb·ft · 236 N·m | +21% 384 |
| Transmission | |||
| Top speed declared | 18.6–24.9 mph · 30–40 km/h | 18.6 mph · 30 km/h | differs |
| Clutch declared | Independent dry double clutch | Dry BORG & BECK double clutch | differs |
| Hydraulics & hitch | |||
| Hydraulic control declared | Constant flow | — | — |
| Pump flow declared | 10.0 gpm · 38.0 L/min | 7.9 gpm · 30.0 L/min | +27% DX 3.50 |
| Three-point lift, at the coupling points declared | 5,291 lb · 2,400 kg | 3,351 lb · 1,520 kg | +58% DX 3.50 |
| Rear PTO speeds declared | 540/1000 rpm | 540 rpm | differs |
| Weight & dimensions | |||
| Unladen weight declared | 6,019–6,878 lb · 2,730–3,120 kg | 4,718 lb · 2,140 kg | differs |
| Maximum permissible mass declared | 10,141 lb · 4,600 kg | — | — |
| Wheelbase declared | 79.2 in · 2,012 mm | 80.0 in · 2,032 mm | — |
| Length declared | 142.9 in · 3,630 mm | 134.0 in · 3,404 mm | +7% DX 3.50 |
| Width declared | 84.2 in · 2,138 mm | 68.6 in · 1,742 mm | +23% DX 3.50 |
| Ground clearance declared | 18.0 in · 457 mm | 18.2 in · 462 mm | — |
| Turning radius, braked declared | 11.8 ft · 3.60 m | 11.3 ft · 3.43 m | — |
| Fuel tank declared | — | 71.9 qt · 68.0 L | — |
Height is not in this table. It is not one measurement: the sources measure it to different points — over the cab on some machines, over the steering wheel or the exhaust on others — and the same tractor measured two ways can differ by most of a metre. It appears here only when both machines' figures carry the point they were measured to and it is the same point, which is not the case for these two. Each machine's own page prints its height as its source gives it.
Deutz-Fahr DX 3.50 sources
- Source: Traktorenlexikon, “Deutz-Fahr DX 3.50”
- Source: Traktorenlexikon, “Fendt Farmer 260 S/SA”
Leyland 384 sources
- Source: Traktorenlexikon, “Leyland 384”