12 material differences
Tractor oneCASE-INTERNATIONAL 595 (DT)1990–1993No measured PTO figureTractor twoSAME Explorer 60 II (DT)1989–1998No measured PTO figure
Which should you choose?
Read our verdict on the 595 (DT) and the Explorer 60 II (DT) → It is generated from the rows below by a fixed, versioned rule set, and names the figure behind every call.
Field by field
12 material differences · 3 fields identical or within 5%, which is not counted as material
| Field | 595 (DT) | Explorer 60 II (DT) | Gap |
|---|---|---|---|
| Engine | |||
| Engine power, claimed claimed | 59.1 hp | 59.1 hp | — |
| Engine declared | IHC D-206 | SAME 1000.3 A | differs |
| Displacement declared | 3.38 L | 3.00 L | +13% 595 (DT) |
| Maximum torque declared | 162 lb·ft · 220 N·m | 151 lb·ft · 205 N·m | +7% 595 (DT) |
| Transmission | |||
| Top speed declared | 18.6 mph · 30 km/h | 18.6–24.9 mph · 30–40 km/h | differs |
| Clutch declared | Pedal-operated dry Laycock single-disc clutch | Pedal-operated dry SAME single disc clutch | differs |
| Hydraulics & hitch | |||
| Hydraulic control declared | — | Load sensing | — |
| Pump flow declared | — | 7.5 gpm · 28.5 L/min | — |
| Pressure declared | — | 1,740 psi · 120 bar | — |
| Three-point lift, at the coupling points declared | 4,409 lb · 2,000 kg | 5,027 lb · 2,280 kg | +14% Explorer 60 II (DT) |
| Rear PTO speeds declared | 540/1000 rpm | 540/540E/1000E/1000 rpm | differs |
| Weight & dimensions | |||
| Unladen weight declared | 6,440 lb · 2,921 kg | 5,600 lb · 2,540 kg | +15% 595 (DT) |
| Wheelbase declared | 84.5 in · 2,146 mm | 86.4 in · 2,195 mm | — |
| Length declared | 142.0 in · 3,607 mm | 135.4 in · 3,440 mm | — |
| Width declared | 75.0 in · 1,905 mm | 70.1–93.7 in · 1,780–2,380 mm | differs |
| Ground clearance declared | 22.1 in · 561 mm | 17.1 in · 435 mm | +29% 595 (DT) |
| Turning radius, braked declared | 11.7 ft · 3.56 m | 9.1 ft · 2.78 m | +28% 595 (DT) |
| Fuel tank declared | 80.0 qt · 75.7 L | 70.8 qt · 67.0 L | +13% 595 (DT) |
Height is not in this table. It is not one measurement: the sources measure it to different points — over the cab on some machines, over the steering wheel or the exhaust on others — and the same tractor measured two ways can differ by most of a metre. It appears here only when both machines' figures carry the point they were measured to and it is the same point, which is not the case for these two. Each machine's own page prints its height as its source gives it.
CASE-INTERNATIONAL 595 (DT) sources
- Source: Traktorenlexikon, “Case-IH 595”
- Source: Traktorenlexikon, “Case-IH 3230”
SAME Explorer 60 II (DT) sources
- Source: Traktorenlexikon, “SAME Explorer II 60”
- Source: Traktorenlexikon, “Lamborghini 600”