11 material differences · fewer than 12
Tractor oneCASE-INTERNATIONAL 495 (DT)1990–1993No measured PTO figureTractor twoFord 3930 (A)1990–1999No measured PTO figure
Which should you choose?
Read our verdict on the 495 (DT) and the 3930 (A) → It is generated from the rows below by a fixed, versioned rule set, and names the figure behind every call.
Field by field
11 material differences · 4 fields identical or within 5%, which is not counted as material
| Field | 495 (DT) | 3930 (A) | Gap |
|---|---|---|---|
| Engine | |||
| Engine power, claimed claimed | 51.2 hp | 50.3 hp | — |
| Engine declared | IHC D-179 | Ford C 201 CID-NA | differs |
| Displacement declared | 2.93 L | 3.29 L | +12% 3930 (A) |
| Maximum torque declared | 134 lb·ft · 182 N·m | 137 lb·ft · 186 N·m | — |
| Transmission | |||
| Top speed declared | 18.6 mph · 30 km/h | 18.6 mph · 30 km/h | — |
| Clutch declared | Pedal-operated dry single-disc clutch and hand lever operated wet multi-disc clutch | Pedal-operated dry AP single-disc clutch | differs |
| Hydraulics & hitch | |||
| Hydraulic centre declared | — | Open centre | — |
| Pump flow declared | 15.6 gpm · 59.2 L/min | 8.8 gpm · 33.2 L/min | +78% 495 (DT) |
| Pressure declared | — | 1,378–1,450 psi · 95–100 bar | — |
| Three-point lift, at the coupling points declared | 3,704 lb · 1,680 kg | 4,299 lb · 1,950 kg | +16% 3930 (A) |
| Rear PTO speeds declared | 540/1000 rpm | 540 rpm | differs |
| Weight & dimensions | |||
| Unladen weight declared | 5,199 lb · 2,358 kg | 6,045 lb · 2,742 kg | +16% 3930 (A) |
| Wheelbase declared | 79.1 in · 2,010 mm | 84.5 in · 2,146 mm | +7% 3930 (A) |
| Length declared | 136.0 in · 3,454 mm | 138.8 in · 3,525 mm | — |
| Width declared | 66.0 in · 1,676 mm | 69.7 in · 1,771 mm | +6% 3930 (A) |
| Ground clearance declared | 22.1 in · 561 mm | 12.2 in · 310 mm | +81% 495 (DT) |
| Turning radius, braked declared | 11.1 ft · 3.38 m | — | — |
| Fuel tank declared | 80.0 qt · 75.7 L | 69.4 qt · 65.7 L | +15% 495 (DT) |
Height is not in this table. It is not one measurement: the sources measure it to different points — over the cab on some machines, over the steering wheel or the exhaust on others — and the same tractor measured two ways can differ by most of a metre. It appears here only when both machines' figures carry the point they were measured to and it is the same point, which is not the case for these two. Each machine's own page prints its height as its source gives it.
CASE-INTERNATIONAL 495 (DT) sources
- Source: Traktorenlexikon, “Case-IH 495”
- Source: Traktorenlexikon, “IHC 553”
Ford 3930 (A) sources
- Source: Traktorenlexikon, “Ford 3930”