12 material differences
Tractor oneAGCO-ALLIS 76501991–1994No measured PTO figureTractor twoDeutz-Fahr IN-trac 6.60 Turbo1986–1991No measured PTO figure
Which should you choose?
Read our verdict on the 7650 and the IN-trac 6.60 Turbo → It is generated from the rows below by a fixed, versioned rule set, and names the figure behind every call.
Field by field
12 material differences · 3 fields identical or within 5%, which is not counted as material
| Field | 7650 | IN-trac 6.60 Turbo | Gap |
|---|---|---|---|
| Engine | |||
| Engine power, claimed claimed | 147.0 hp | 148 hp | — |
| Engine declared | S.L.H. 1056 PS | KHD BF6L 913 | differs |
| Displacement declared | 6.24 L | 6.13 L | — |
| Maximum torque declared | 359 lb·ft · 487 N·m | 395 lb·ft · 535 N·m | +10% IN-trac 6.60 Turbo |
| Transmission | |||
| Top speed declared | 18.6 mph · 30 km/h | 18.6–24.9 mph · 30–40 km/h | differs |
| Clutch declared | Pedal-operated dry S.L.H. double clutch | Hydraulic clutch | differs |
| Hydraulics & hitch | |||
| Hydraulic centre declared | Open centre | — | — |
| Hydraulic control declared | Load sensing | — | — |
| Pump flow declared | 17.7 gpm · 67.0 L/min | 14.8 gpm · 56.0 L/min | +20% 7650 |
| Pressure declared | 3,046 psi · 210 bar | — | — |
| Rear PTO speeds declared | 540/1000 rpm | 540/1000 rpm | — |
| Weight & dimensions | |||
| Unladen weight declared | 12,566 lb · 5,700 kg | 13,889 lb · 6,300 kg | +11% IN-trac 6.60 Turbo |
| Maximum permissible mass declared | 18,739 lb · 8,500 kg | 22,046 lb · 10,000 kg | +18% IN-trac 6.60 Turbo |
| Wheelbase declared | 114.2 in · 2,901 mm | 106.4 in · 2,703 mm | +7% 7650 |
| Length declared | 185.2 in · 4,704 mm | 204.7 in · 5,199 mm | +11% IN-trac 6.60 Turbo |
| Width declared | 86.0 in · 2,184 mm | 94.1 in · 2,390 mm | +9% IN-trac 6.60 Turbo |
| Ground clearance declared | 20.4 in · 518 mm | 22.8 in · 580 mm | +12% IN-trac 6.60 Turbo |
| Turning radius, braked declared | 17.2 ft · 5.25 m | — | — |
| Fuel tank declared | 221.9 qt · 210.0 L | 285.3 qt · 270 L | +29% IN-trac 6.60 Turbo |
Height is not in this table. It is not one measurement: the sources measure it to different points — over the cab on some machines, over the steering wheel or the exhaust on others — and the same tractor measured two ways can differ by most of a metre. It appears here only when both machines' figures carry the point they were measured to and it is the same point, which is not the case for these two. Each machine's own page prints its height as its source gives it.
AGCO-ALLIS 7650 sources
Source
- Source: Traktorenlexikon, “AGCO-Allis 7650”
Deutz-Fahr IN-trac 6.60 Turbo sources
Source
- Source: Traktorenlexikon, “Deutz-Fahr IN-trac 6.60 turbo”
- Source: Traktorenlexikon, “Deutz-Fahr DX 160”