WhichTractor
  • Crawler
  • WhichTractor size: Utility
  • Not independently tested
  • 1968–1974

It was ranked on an engine power figure whose source does not say gross or net. WhichTractor size, not the maker’s category

Derived by WhichTractor from a sourced three-point linkage. How we decide what a machine is

Fiat 355 C Full specifications

FIAT-IVECO 8025.02.011 two-cylinder diesel. The manufacturer claimed 34.5 horsepower. No laboratory has tested one, so there is no measured figure at the shaft.

Engine power, claimed · gross or net not stated

34.5 hp

25.7 kW as stated by the source

Not independently tested

Claimed · standard not stated by the source

Source · Traktorenlexikon, “Fiat 355 C”, claimed

Weight
4,486 lb
Hyd. flow
4.9 gpm
Top speed
6.8 mph

Fiat 355 C specs: key facts

  • The Fiat 355 C was built from 1968 to 1974.

  • The Fiat 355 C has a claimed engine power (gross or net not stated) of 25.7 kW (34.5 hp); it has no measured PTO figure.

  • The Fiat 355 C is a tracked machine.

  • The Fiat 355 C has a FIAT-IVECO 8025.02.011 engine, a 2-cylinder 1.73 L diesel unit.

  • The Fiat 355 C weighs 2,035 kg (4,486 lb) unladen.

  • The Fiat 355 C has a rear PTO running at 540 rpm.

  • The hydraulic pump of the Fiat 355 C delivers 18.5 L/min (4.9 gpm).

Source · Traktorenlexikon, “Fiat 355 C”

How much horsepower does a 355 C have?

The only figure for the 355 C is 34.5 hp (25.7 kW) of claimed engine power, gross or net not stated, no test standard stated — not power at the shaft.

Engine, claimed (gross/net not stated)
34.5 hp

Source · Traktorenlexikon, “Fiat 355 C”

What engine is in a 355 C?

A 355 C has a FIAT-IVECO 8025.02.011, a 2-cylinder 1.73 L diesel engine.

Engine — 355 C engine specifications
Make & modelFIAT-IVECO 8025.02.011
Cylinders2, liquid-cooled
Displacement105.4 ci · 1.73 L
Max torque83 lb·ft · 112 N·m @ 1,400 rpm
Injectiondirect injection
Electrical system12 V

Source · Traktorenlexikon, “Fiat 355 C”

How much will a 355 C lift, and what is its hydraulic flow?

Hydraulic and PTO specifications for the 355 C are below.

Hydraulics & PTO — 355 C hydraulics and PTO specifications
Pump flow4.9 gpm · 18.5 L/min
Pressure2,843 psi · 196 bar
Hitch categoryCategory 1
Rear PTO540 rpm @ 2,160 engine rpm
PTO shaft1 3/8"- 6 splines

Source · Traktorenlexikon, “Fiat 355 C”

What transmission does a 355 C have?

Transmission specifications for the 355 C are below.

Transmission — 355 C transmission specifications
Clutchhand-lever operated dry single-plate clutch with dead-center engagement
Top speed6.8 mph · 11 km/h

Source · Traktorenlexikon, “Fiat 355 C”

How much does a 355 C weigh?

A 355 C weighs 4,486 lb (2,035 kg) unladen.

Weights & dimensions — 355 C weights and dimensions
Unladen weight4,486 lb · 2,035 kg
Wheelbase50.9 in · 1,293 mm
Length96.9 in · 2,460 mm
Width46.5 in · 1,182 mm
Height44.3 in · 1,125 mm
Ground clearance9.8 in · 250 mm
Front track35.4 in · 900 mmWikibooks gives one track for both axles
Rear track35.4 in · 900 mmWikibooks gives one track for both axles

Source · Traktorenlexikon, “Fiat 355 C”

Everything else people ask

Is a 355 C two-wheel drive or four-wheel drive?

The Fiat 355 C is a tracked machine.

What PTO does a 355 C have?

A 355 C has a 540 rpm rear PTO on a 1 3/8"- 6 splines shaft.

Where this page comes from

Compiled from Traktorenlexikon, “Fiat 355 C”.

Last verified

Not yet verified

Spotted an error?

Sources

Facts taken from these documents, units converted. Numbers beside a figure refer to this list. Licences and attribution

  1. Traktorenlexikon: Fiat 355 C — CC BY-SA 4.0, WIKIBOOKS-TL-121932 · revision 1076574. Wikibooks contributors (Traktorenlexikon). Original document