7 material differences · fewer than 12
Tractor oneSOMECA 480-8 (TD)1981–1982No measured PTO figureTractor twoSOMECA 500 (TD)1971–1973No measured PTO figure
Which should you choose?
Read our verdict on the 480-8 (TD) and the 500 (TD) → It is generated from the rows below by a fixed, versioned rule set, and names the figure behind every call.
Field by field
7 material differences · 10 fields identical or within 5%, which is not counted as material
| Field | 480-8 (TD) | 500 (TD) | Gap |
|---|---|---|---|
| Engine | |||
| Engine power, claimed claimed | 47.3 hp | 47.3 hp | — |
| Engine declared | FIAT-IVECO 8035.02.200 (300) | FIAT-IVECO 8035.02.202 | differs |
| Displacement declared | 2.59 L | 2.59 L | — |
| Maximum torque declared | 112 lb·ft · 152 N·m | 118 lb·ft · 160 N·m | +5% 500 (TD) |
| Transmission | |||
| Top speed declared | 15.5 mph · 25 km/h | 15.5 mph · 25 km/h | — |
| Clutch declared | Dry FERODO double clutch | Pedal-operated two-stage dry FERODO double clutch | differs |
| Hydraulics & hitch | |||
| Pump flow declared | 7.1 gpm · 26.8 L/min | 5.8 gpm · 21.8 L/min | +23% 480-8 (TD) |
| Pressure declared | 2,843 psi · 196 bar | 2,843 psi · 196 bar | — |
| Three-point lift, at the coupling points declared | 3,858 lb · 1,750 kg | 3,417 lb · 1,550 kg | +13% 480-8 (TD) |
| Rear PTO speeds declared | 540 rpm | 540 rpm | — |
| Weight & dimensions | |||
| Unladen weight declared | 3,990 lb · 1,810 kg | 4,023 lb · 1,825 kg | — |
| Wheelbase declared | 76.9 in · 1,953 mm | 75.6 in · 1,920 mm | — |
| Length declared | 114.6 in · 2,910 mm | 119.1 in · 3,025 mm | — |
| Width declared | 70.5 in · 1,790 mm | 62.4–92.9 in · 1,585–2,360 mm | differs |
| Ground clearance declared | 17.9 in · 455 mm | 15.0 in · 380 mm | +20% 480-8 (TD) |
| Turning radius, braked declared | 9.7 ft · 2.95 m | 9.7 ft · 2.95 m | — |
| Fuel tank declared | 57.1 qt · 54.0 L | 57.1 qt · 54.0 L | — |
Height is not in this table. It is not one measurement: the sources measure it to different points — over the cab on some machines, over the steering wheel or the exhaust on others — and the same tractor measured two ways can differ by most of a metre. It appears here only when both machines' figures carry the point they were measured to and it is the same point, which is not the case for these two. Each machine's own page prints its height as its source gives it.
SOMECA 480-8 (TD) sources
- Source: Traktorenlexikon, “Someca 480-8”
- Source: Traktorenlexikon, “Fiat 480/480 DT”
SOMECA 500 (TD) sources
- Source: Traktorenlexikon, “Someca 500”