13 material differences
Tractor oneSOMECA 1380 (TD)1979–1983No measured PTO figureTractor twoVALMET 15021975–1980No measured PTO figure
Which should you choose?
Read our verdict on the 1380 (TD) and the 1502 → It is generated from the rows below by a fixed, versioned rule set, and names the figure behind every call.
Field by field
13 material differences · 1 fields identical or within 5%, which is not counted as material
| Field | 1380 (TD) | 1502 | Gap |
|---|---|---|---|
| Engine | |||
| Engine power, claimed claimed | 133.2 hp | 134 hp | — |
| Engine declared | FIAT-IVECO 8065.24.000 | VALMET 611 CS | differs |
| Displacement declared | 5.50 L | 6.60 L | +20% 1502 |
| Maximum torque declared | 347 lb·ft · 470 N·m | 406 lb·ft · 550 N·m | +17% 1502 |
| Transmission | |||
| Top speed declared | 15.5–18.6 mph · 25–30 km/h | 18.6 mph · 30 km/h | differs |
| Clutch declared | Pedal operated Ferodo or LuK single-disc clutch | Dry Fichtel & Sachs double clutch | differs |
| Hydraulics & hitch | |||
| Pump flow declared | 14.1 gpm · 53.5 L/min | — | — |
| Pressure declared | 3,263–3,408 psi · 225–235 bar | — | — |
| Three-point lift, at the coupling points declared | 10,878 lb · 4,934 kg | 7,871 lb · 3,570 kg | +38% 1380 (TD) |
| Rear PTO speeds declared | 1000 rpm | 540/1000 rpm | differs |
| Weight & dimensions | |||
| Unladen weight declared | 10,748 lb · 4,875 kg | 16,469 lb · 7,470 kg | +53% 1502 |
| Maximum permissible mass declared | 19,070 lb · 8,650 kg | — | — |
| Wheelbase declared | 108.3 in · 2,750 mm | 101.3 in · 2,572 mm | +7% 1380 (TD) |
| Length declared | 162.8 in · 4,135 mm | 209.8 in · 5,330 mm | +29% 1502 |
| Width declared | 85.0–108.7 in · 2,160–2,760 mm | 83.7 in · 2,125 mm | differs |
| Ground clearance declared | 26.2 in · 665 mm | 16.5 in · 420 mm | +58% 1380 (TD) |
| Turning radius, braked declared | 13.9 ft · 4.25 m | — | — |
| Fuel tank declared | 295.9 qt · 280.0 L | 190.2 qt · 180.0 L | +56% 1380 (TD) |
Height is not in this table. It is not one measurement: the sources measure it to different points — over the cab on some machines, over the steering wheel or the exhaust on others — and the same tractor measured two ways can differ by most of a metre. It appears here only when both machines' figures carry the point they were measured to and it is the same point, which is not the case for these two. Each machine's own page prints its height as its source gives it.
SOMECA 1380 (TD) sources
Source
- Source: Traktorenlexikon, “Someca 1380”
- Source: Traktorenlexikon, “Fiat 1380 (DT)”
VALMET 1502 sources
Source
- Source: Traktorenlexikon, “Valmet 1502”