Lanz D 7006 or MAN AS 325?
Which should you choose?
On performance, no comparable figure differs by more than its threshold: on this data the machines are level. On features, the MAN AS 325 is ahead on top speed and drive.
- The MAN AS 325 suits road haulage better on this data: 28% (4.2 km/h / 2.6 mph) more top speed.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | D 7006 | AS 325 | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 18.4 kW (25 hp)Traktorenlexikon, “Lanz D 7006 Reingas” | 18.4 kW (25 hp)Traktorenlexikon, “MAN AS 325” | EvenEven on power at the PTO shaft (both power at the PTO, claimed): the difference is under the 10% threshold for claimed figures, too small to call. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the D 7006 and the AS 325. |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the D 7006 and the AS 325. |
| Which pumps more oil for implements? | — | — | No figureNo call on hydraulic flow: no figure on record for the D 7006 and the AS 325. |
| Which lifts more on the three-point hitch? | — | — | No figureNo call on three-point lift: no figure on record for the D 7006 and the AS 325. |
| Which is heavier, for traction? | 2,360 kg (5,203 lb)Traktorenlexikon, “Lanz D 7006 Reingas” | 1,770 kg (3,902 lb)Traktorenlexikon, “MAN AS 325” | Ahead (a fact, not an advantage)The Lanz D 7006 is 33% heavier (590 kg / 1,301 lb) than the MAN AS 325 (both unladen weight, as stated by the source). |
| Which may carry more ballast and load? | — | 2,700 kg (5,952 lb)Traktorenlexikon, “MAN AS 325” | No figureNo call on maximum permissible mass: no figure on record for the D 7006. |
| Which has the wider choice of gears? | 6Traktorenlexikon, “Lanz D 7006 Reingas” | 5Traktorenlexikon, “MAN AS 325” | EvenEven on forward gears (both forward gears, as stated by the source): the difference is under the 25% threshold, too small to call. |
| Which offers a creeper range? | — | — | No figureNo call on a creeper range: not stated for the D 7006 and the AS 325. |
| Which is faster on the road? | 15.1 km/h (9.4 mph)Traktorenlexikon, “Lanz D 7006 Reingas” | 19.3 km/h (12.0 mph) to 20.0 km/h (12.4 mph)Traktorenlexikon, “MAN AS 325” | AheadThe MAN AS 325 has 28% more top speed (4.2 km/h / 2.6 mph) than the Lanz D 7006 (both top speed forward, as stated by the source). |
| Which offers more PTO speeds? | 850Traktorenlexikon, “Lanz D 7006 Reingas” | 540 rpmTraktorenlexikon, “MAN AS 325” | No figureNo call on PTO speeds: no standard PTO speed stated for the D 7006. |
| Which PTO runs independently of the ground drive? | — | — | No figureNo call on PTO independence: not stated for the D 7006 and the AS 325. |
| Which drives on both axles? | 2WDTraktorenlexikon, “Lanz D 7006 Reingas” | Two-wheel or four-wheel driveTraktorenlexikon, “MAN AS 325” | AheadThe MAN AS 325 is available with four-wheel drive; the Lanz D 7006 is two-wheel drive (as stated by the sources). |
| Which is newer, and what about parts? | 1943–1945 | 1948–1955 | Ahead (a fact, not an advantage)The MAN AS 325 is newer: production began 5 years later. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The Lanz D 7006 is 33% heavier (590 kg / 1,301 lb) than the MAN AS 325 (both unladen weight, as stated by the source).
- The MAN AS 325 has 28% more top speed (4.2 km/h / 2.6 mph) than the Lanz D 7006 (both top speed forward, as stated by the source).
- The MAN AS 325 is available with four-wheel drive; the Lanz D 7006 is two-wheel drive (as stated by the sources).
- The MAN AS 325 is newer: production began 5 years later. We hold no parts-availability data, so there is no call on parts.
- Even on power at the PTO shaft (both power at the PTO, claimed): the difference is under the 10% threshold for claimed figures, too small to call.
- Even on forward gears (both forward gears, as stated by the source): the difference is under the 25% threshold, too small to call.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, hydraulic flow, three-point lift, maximum permissible mass, a creeper range, PTO speeds and PTO independence.
← Every figure for both machines, side by side, with sources