9 material differences · fewer than 12
Tractor oneLandini R-8860 (DT) TL-23 N/M (TL-23 DT/M)1988–2000No measured PTO figureTractor twoVALMET 655/655-41988–1989No measured PTO figure
Which should you choose?
Read our verdict on the R-8860 (DT) TL-23 N/M (TL-23 DT/M) and the 655/655-4 → It is generated from the rows below by a fixed, versioned rule set, and names the figure behind every call.
Field by field
9 material differences · 4 fields identical or within 5%, which is not counted as material
| Field | R-8860 (DT) TL-23 N/M (TL-23 DT/M) | 655/655-4 | Gap |
|---|---|---|---|
| Engine | |||
| Engine power, claimed claimed | 78.9 hp | 78.9 hp | — |
| Engine declared | Perkins LF 4.248 | VALMET D 44 D-7 | differs |
| Displacement declared | 4.06 L | 4.40 L | +8% 655/655-4 |
| Maximum torque declared | 215 lb·ft · 291 N·m | 221 lb·ft · 300 N·m | — |
| Transmission | |||
| Top speed declared | 18.6 mph · 30 km/h | 18.6 mph · 30 km/h | — |
| Clutch declared | Dry and air-cooled OMG double clutch | — | — |
| Hydraulics & hitch | |||
| Pump flow declared | 9.3 gpm · 35.3 L/min | — | — |
| Pressure declared | 2,756 psi · 190 bar | — | — |
| Three-point lift, at the coupling points declared | 4,343 lb · 1,970 kg | 9,921 lb · 4,500 kg | +128% 655/655-4 |
| Rear PTO speeds declared | 540/1000 rpm | 540 rpm | differs |
| Weight & dimensions | |||
| Unladen weight declared | 6,437 lb · 2,920 kg | 8,289 lb · 3,760 kg | +29% 655/655-4 |
| Wheelbase declared | 92.2 in · 2,341 mm | 93.9 in · 2,385 mm | — |
| Length declared | 150.0 in · 3,810 mm | 177.8 in · 4,515 mm | +19% 655/655-4 |
| Width declared | 77.8 in · 1,975 mm | 83.9 in · 2,130 mm | +8% 655/655-4 |
| Ground clearance declared | 21.3 in · 540 mm | 18.7 in · 475 mm | +14% R-8860 (DT) TL-23 N/M (TL-23 DT/M) |
| Turning radius, braked declared | 13.5 ft · 4.11 m | — | — |
| Fuel tank declared | 90.9 qt · 86.0 L | 190.2 qt · 180.0 L | +109% 655/655-4 |
Height is not in this table. It is not one measurement: the sources measure it to different points — over the cab on some machines, over the steering wheel or the exhaust on others — and the same tractor measured two ways can differ by most of a metre. It appears here only when both machines' figures carry the point they were measured to and it is the same point, which is not the case for these two. Each machine's own page prints its height as its source gives it.
Landini R-8860 (DT) TL-23 N/M (TL-23 DT/M) sources
- Source: Traktorenlexikon, “Landini 8860”
VALMET 655/655-4 sources
- Source: Traktorenlexikon, “Valmet 655”