2 material differences · fewer than 12
Tractor oneLandini R-7860 (DT) TL-20 N/M (TL-20 DT/M)1988–2000No measured PTO figureTractor twoMassey Ferguson MF 383 (A)1987–1994No measured PTO figure
Which should you choose?
Read our verdict on the R-7860 (DT) TL-20 N/M (TL-20 DT/M) and the MF 383 (A) → It is generated from the rows below by a fixed, versioned rule set, and names the figure behind every call.
Field by field
2 material differences · 14 fields identical or within 5%, which is not counted as material
| Field | R-7860 (DT) TL-20 N/M (TL-20 DT/M) | MF 383 (A) | Gap |
|---|---|---|---|
| Engine | |||
| Engine power, claimed claimed | 70.0 hp | 70.1 hp | — |
| Engine declared | Perkins LD 4.236 | Perkins A 4.236 | differs |
| Displacement declared | 3.87 L | 3.87 L | — |
| Maximum torque declared | 195 lb·ft · 264 N·m | 195 lb·ft · 264 N·m | — |
| Transmission | |||
| Top speed declared | 18.6 mph · 30 km/h | 18.6 mph · 30 km/h | — |
| Clutch declared | Dry and air-cooled OMG double clutch | Dry and air-cooled OMG double clutch | — |
| Hydraulics & hitch | |||
| Hydraulic centre declared | — | Open centre | — |
| Pump flow declared | 9.8 gpm · 37.2 L/min | — | — |
| Pressure declared | 2,756 psi · 190 bar | 2,756 psi · 190 bar | — |
| Three-point lift, at the coupling points declared | 4,698 lb · 2,131 kg | 5,291 lb · 2,400 kg | +13% MF 383 (A) |
| Rear PTO speeds declared | 540/1000 rpm | 540/1000 rpm | — |
| Weight & dimensions | |||
| Unladen weight declared | 6,305 lb · 2,860 kg | 6,305 lb · 2,860 kg | — |
| Wheelbase declared | 89.8 in · 2,281 mm | 89.8 in · 2,281 mm | — |
| Length declared | 146.1 in · 3,710 mm | 146.1 in · 3,710 mm | — |
| Width declared | 78.3 in · 1,990 mm | 78.3 in · 1,990 mm | — |
| Ground clearance declared | 20.3 in · 515 mm | 20.3 in · 515 mm | — |
| Turning radius, braked declared | 13.0 ft · 3.96 m | 13.0 ft · 3.96 m | — |
| Fuel tank declared | 90.9 qt · 86.0 L | 90.9 qt · 86.0 L | — |
Height is not in this table. It is not one measurement: the sources measure it to different points — over the cab on some machines, over the steering wheel or the exhaust on others — and the same tractor measured two ways can differ by most of a metre. It appears here only when both machines' figures carry the point they were measured to and it is the same point, which is not the case for these two. Each machine's own page prints its height as its source gives it.
Landini R-7860 (DT) TL-20 N/M (TL-20 DT/M) sources
- Source: Traktorenlexikon, “Landini 7860”
- Source: Traktorenlexikon, “Massey Ferguson MF 373”
Massey Ferguson MF 383 (A) sources
- Source: Traktorenlexikon, “Massey Ferguson MF 383”
- Source: Traktorenlexikon, “Massey Ferguson MF 168 & MF 168A”