5 material differences · fewer than 12
Tractor oneLandini R-7860 (DT) TL-20 N/M (TL-20 DT/M)1988–2000No measured PTO figureTractor twoMassey Ferguson MF 2831983–1987No measured PTO figure
Which should you choose?
We will not advise between these two machines, because they were not built in overlapping years (1988–2000; 1983–1987). The figures below are side by side so you can judge them yourself; each says whether it was measured, claimed or declared by its source.
Field by field
5 material differences · 8 fields identical or within 5%, which is not counted as material
| Field | R-7860 (DT) TL-20 N/M (TL-20 DT/M) | MF 283 | Gap |
|---|---|---|---|
| Engine | |||
| Engine power, claimed claimed | 70.0 hp | 70 hp | — |
| Engine declared | Perkins LD 4.236 | Perkins A 4.236 | differs |
| Displacement declared | 3.87 L | 3.87 L | — |
| Maximum torque declared | 195 lb·ft · 264 N·m | 202 lb·ft · 274 N·m | — |
| Transmission | |||
| Top speed declared | 18.6 mph · 30 km/h | 21.7 mph · 35 km/h | +17% MF 283 |
| Clutch declared | Dry and air-cooled OMG double clutch | Two stage clutch | differs |
| Hydraulics & hitch | |||
| Pump flow declared | 9.8 gpm · 37.2 L/min | 9.5 gpm · 36.0 L/min | — |
| Pressure declared | 2,756 psi · 190 bar | — | — |
| Rear PTO speeds declared | 540/1000 rpm | 750 rpm | differs |
| Weight & dimensions | |||
| Unladen weight declared | 6,305 lb · 2,860 kg | 6,118 lb · 2,775 kg | — |
| Wheelbase declared | 89.8 in · 2,281 mm | 90.6 in · 2,300 mm | — |
| Length declared | 146.1 in · 3,710 mm | 146.9 in · 3,730 mm | — |
| Width declared | 78.3 in · 1,990 mm | 79.1 in · 2,010 mm | — |
| Ground clearance declared | 20.3 in · 515 mm | 16.1 in · 410 mm | +26% R-7860 (DT) TL-20 N/M (TL-20 DT/M) |
| Turning radius, braked declared | 13.0 ft · 3.96 m | — | — |
| Fuel tank declared | 90.9 qt · 86.0 L | — | — |
Height is not in this table. It is not one measurement: the sources measure it to different points — over the cab on some machines, over the steering wheel or the exhaust on others — and the same tractor measured two ways can differ by most of a metre. It appears here only when both machines' figures carry the point they were measured to and it is the same point, which is not the case for these two. Each machine's own page prints its height as its source gives it.
Landini R-7860 (DT) TL-20 N/M (TL-20 DT/M) sources
- Source: Traktorenlexikon, “Landini 7860”
- Source: Traktorenlexikon, “Massey Ferguson MF 373”
Massey Ferguson MF 283 sources
- Source: Traktorenlexikon, “Massey Ferguson MF 283”
- Source: Traktorenlexikon, “Massey Ferguson MF 168 & MF 168A”