Landini 7830 (DT) TL-20 N/F (TL-20 DT/F) or SAME Centurion 75 (DT)?
Which should you choose?
The data can’t decide this. Power at the PTO shaft cannot be compared: the 7830 (DT) TL-20 N/F (TL-20 DT/F) has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the Centurion 75 (DT) has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- The Landini 7830 (DT) TL-20 N/F (TL-20 DT/F) suits loader and hydraulic implement work better on this data: 76% (16.7 L/min / 4.4 gpm) more hydraulic flow and 13% (350 kg / 772 lb) more three-point lift.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | 7830 (DT) TL-20 N/F (TL-20 DT/F) | Centurion 75 (DT) | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 53 kW (71 hp)Traktorenlexikon, “Landini 7830 (DT)” | 53.7 kW (72.0 hp)Traktorenlexikon, “SAME Centurion 75” | Not comparableNot comparable on power at the PTO shaft: the 7830 (DT) TL-20 N/F (TL-20 DT/F) has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the Centurion 75 (DT) has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the 7830 (DT) TL-20 N/F (TL-20 DT/F) and the Centurion 75 (DT). |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the 7830 (DT) TL-20 N/F (TL-20 DT/F) and the Centurion 75 (DT). |
| Which pumps more oil for implements? | 38.7 L/min (10.2 gpm)Traktorenlexikon, “Landini 7830 (DT)” | 22.0 L/min (5.8 gpm)Traktorenlexikon, “SAME Centurion 75” | AheadThe Landini 7830 (DT) TL-20 N/F (TL-20 DT/F) has 76% more hydraulic flow (16.7 L/min / 4.4 gpm) than the SAME Centurion 75 (DT) (both pump flow, as stated by the source). |
| Which lifts more on the three-point hitch? | 3,050 kg (6,724 lb)Traktorenlexikon, “Landini 7830 (DT)” | 2,700 kg (5,952 lb)Traktorenlexikon, “SAME Centurion 75” | AheadThe Landini 7830 (DT) TL-20 N/F (TL-20 DT/F) has 13% more lift (350 kg / 772 lb) than the SAME Centurion 75 (DT) (both lift at the hitch ends, as stated by the source). |
| Which is heavier, for traction? | 2,715 kg (5,986 lb)Traktorenlexikon, “Landini 7830 (DT)” | 3,270 kg (7,209 lb)Traktorenlexikon, “SAME Centurion 75” | Ahead (a fact, not an advantage)The SAME Centurion 75 (DT) is 20% heavier (555 kg / 1,224 lb) than the Landini 7830 (DT) TL-20 N/F (TL-20 DT/F) (both unladen weight, as stated by the source). |
| Which may carry more ballast and load? | — | — | No figureNo call on maximum permissible mass: no figure on record for the 7830 (DT) TL-20 N/F (TL-20 DT/F) and the Centurion 75 (DT). |
| Which has the wider choice of gears? | 12Traktorenlexikon, “Landini 7830 (DT)” | 12 to 16Traktorenlexikon, “SAME Centurion 75” | EvenEven on forward gears (both forward gears, as stated by the source): the figures vary by configuration and the ranges overlap. |
| Which offers a creeper range? | — | — | No figureNo call on a creeper range: not stated for the 7830 (DT) TL-20 N/F (TL-20 DT/F) and the Centurion 75 (DT). |
| Which is faster on the road? | 30 km/h (18.6 mph)Traktorenlexikon, “Landini 7830 (DT)” | 25 km/h (15.5 mph) to 30 km/h (18.6 mph)Traktorenlexikon, “SAME Centurion 75” | EvenEven on top speed (both top speed forward, as stated by the source): the figures vary by configuration and the ranges overlap. |
| Which offers more PTO speeds? | 540/1000 rpmTraktorenlexikon, “Landini 7830 (DT)” | 540/1000 rpmTraktorenlexikon, “SAME Centurion 75” | EvenEven on PTO speeds: the same speeds (540, 1000 rpm). |
| Which PTO runs independently of the ground drive? | — | — | No figureNo call on PTO independence: not stated for the 7830 (DT) TL-20 N/F (TL-20 DT/F) and the Centurion 75 (DT). |
| Which drives on both axles? | Two-wheel or four-wheel driveTraktorenlexikon, “Landini 7830 (DT)” | Two-wheel or four-wheel driveTraktorenlexikon, “SAME Centurion 75” | EvenEven on drive: every machine is available with four-wheel drive. |
| Which is newer, and what about parts? | 1983–1987 | 1978–1985 | Ahead (a fact, not an advantage)The Landini 7830 (DT) TL-20 N/F (TL-20 DT/F) is newer: production began 5 years later. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The Landini 7830 (DT) TL-20 N/F (TL-20 DT/F) has 76% more hydraulic flow (16.7 L/min / 4.4 gpm) than the SAME Centurion 75 (DT) (both pump flow, as stated by the source).
- The Landini 7830 (DT) TL-20 N/F (TL-20 DT/F) has 13% more lift (350 kg / 772 lb) than the SAME Centurion 75 (DT) (both lift at the hitch ends, as stated by the source).
- The SAME Centurion 75 (DT) is 20% heavier (555 kg / 1,224 lb) than the Landini 7830 (DT) TL-20 N/F (TL-20 DT/F) (both unladen weight, as stated by the source).
- The Landini 7830 (DT) TL-20 N/F (TL-20 DT/F) is newer: production began 5 years later. We hold no parts-availability data, so there is no call on parts.
- Even on forward gears (both forward gears, as stated by the source): the figures vary by configuration and the ranges overlap.
- Even on top speed (both top speed forward, as stated by the source): the figures vary by configuration and the ranges overlap.
- Even on PTO speeds: the same speeds (540, 1000 rpm).
- Even on drive: every machine is available with four-wheel drive.
- Not comparable on power at the PTO shaft: the 7830 (DT) TL-20 N/F (TL-20 DT/F) has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the Centurion 75 (DT) has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, maximum permissible mass, a creeper range and PTO independence.
← Every figure for both machines, side by side, with sources