Landini 5860 (DT) TL-22 N/K (TL-22 DT/K) or URSUS C-360 3P?
Which should you choose?
The data can’t decide this. Power at the PTO shaft cannot be compared: the 5860 (DT) TL-22 N/K (TL-22 DT/K) has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the C-360 3P has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- The Landini 5860 (DT) TL-22 N/K (TL-22 DT/K) suits loader and hydraulic implement work better on this data: 76% (16.4 L/min / 4.3 gpm) more hydraulic flow and 70% (840 kg / 1,852 lb) more three-point lift.
- The Landini 5860 (DT) TL-22 N/K (TL-22 DT/K) suits heavy draft work (ploughing, cultivating) better on this data: four-wheel drive.
- The Landini 5860 (DT) TL-22 N/K (TL-22 DT/K) suits road haulage better on this data: 20% (5.0 km/h / 3.1 mph) more top speed.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | 5860 (DT) TL-22 N/K (TL-22 DT/K) | C-360 3P | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 34.6 kW (46.4 hp)Traktorenlexikon, “Landini 5860” | 34.9 kW (46.8 hp)Traktorenlexikon, “Ursus C-360-3P” | Not comparableNot comparable on power at the PTO shaft: the 5860 (DT) TL-22 N/K (TL-22 DT/K) has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the C-360 3P has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the 5860 (DT) TL-22 N/K (TL-22 DT/K) and the C-360 3P. |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the 5860 (DT) TL-22 N/K (TL-22 DT/K) and the C-360 3P. |
| Which pumps more oil for implements? | 37.9 L/min (10.0 gpm)Traktorenlexikon, “Landini 5860” | 21.5 L/min (5.7 gpm)Traktorenlexikon, “Ursus C-360-3P” | AheadThe Landini 5860 (DT) TL-22 N/K (TL-22 DT/K) has 76% more hydraulic flow (16.4 L/min / 4.3 gpm) than the URSUS C-360 3P (both pump flow, as stated by the source). |
| Which lifts more on the three-point hitch? | 2,040 kg (4,497 lb)Traktorenlexikon, “Landini 5860” | 1,200 kg (2,646 lb)Traktorenlexikon, “Ursus C-360-3P” | AheadThe Landini 5860 (DT) TL-22 N/K (TL-22 DT/K) has 70% more lift (840 kg / 1,852 lb) than the URSUS C-360 3P (both lift at the hitch ends, as stated by the source). |
| Which is heavier, for traction? | 2,250 kg (4,960 lb)Traktorenlexikon, “Landini 5860” | 2,056 kg (4,533 lb)Traktorenlexikon, “Ursus C-360-3P” | EvenEven on weight (both unladen weight, as stated by the source): the difference is under the 10% threshold, too small to call. |
| Which may carry more ballast and load? | — | — | No figureNo call on maximum permissible mass: no figure on record for the 5860 (DT) TL-22 N/K (TL-22 DT/K) and the C-360 3P. |
| Which has the wider choice of gears? | 12 to 24Traktorenlexikon, “Landini 5860” | 10Traktorenlexikon, “Ursus C-360-3P” | EvenEven on forward gears (both forward gears, as stated by the source): the difference is under the 25% threshold, too small to call. |
| Which offers a creeper range? | — | — | No figureNo call on a creeper range: not stated for the 5860 (DT) TL-22 N/K (TL-22 DT/K) and the C-360 3P. |
| Which is faster on the road? | 30 km/h (18.6 mph)Traktorenlexikon, “Landini 5860” | 25 km/h (15.5 mph)Traktorenlexikon, “Ursus C-360-3P” | AheadThe Landini 5860 (DT) TL-22 N/K (TL-22 DT/K) has 20% more top speed (5.0 km/h / 3.1 mph) than the URSUS C-360 3P (both top speed forward, as stated by the source). |
| Which offers more PTO speeds? | 540/1000 rpmTraktorenlexikon, “Landini 5860” | 540 rpmTraktorenlexikon, “Ursus C-360-3P” | AheadThe Landini 5860 (DT) TL-22 N/K (TL-22 DT/K) offers 1000 rpm at the PTO, which the URSUS C-360 3P does not (as stated by the sources). |
| Which PTO runs independently of the ground drive? | — | — | No figureNo call on PTO independence: not stated for the 5860 (DT) TL-22 N/K (TL-22 DT/K) and the C-360 3P. |
| Which drives on both axles? | Two-wheel or four-wheel driveTraktorenlexikon, “Landini 5860” | 2WDTraktorenlexikon, “Ursus C-360-3P” | AheadThe Landini 5860 (DT) TL-22 N/K (TL-22 DT/K) is available with four-wheel drive; the URSUS C-360 3P is two-wheel drive (as stated by the sources). |
| Which is newer, and what about parts? | 1988–2000 | 1981–1993 | Ahead (a fact, not an advantage)The Landini 5860 (DT) TL-22 N/K (TL-22 DT/K) is newer: production began 7 years later. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The Landini 5860 (DT) TL-22 N/K (TL-22 DT/K) has 76% more hydraulic flow (16.4 L/min / 4.3 gpm) than the URSUS C-360 3P (both pump flow, as stated by the source).
- The Landini 5860 (DT) TL-22 N/K (TL-22 DT/K) has 70% more lift (840 kg / 1,852 lb) than the URSUS C-360 3P (both lift at the hitch ends, as stated by the source).
- The Landini 5860 (DT) TL-22 N/K (TL-22 DT/K) has 20% more top speed (5.0 km/h / 3.1 mph) than the URSUS C-360 3P (both top speed forward, as stated by the source).
- The Landini 5860 (DT) TL-22 N/K (TL-22 DT/K) offers 1000 rpm at the PTO, which the URSUS C-360 3P does not (as stated by the sources).
- The Landini 5860 (DT) TL-22 N/K (TL-22 DT/K) is available with four-wheel drive; the URSUS C-360 3P is two-wheel drive (as stated by the sources).
- The Landini 5860 (DT) TL-22 N/K (TL-22 DT/K) is newer: production began 7 years later. We hold no parts-availability data, so there is no call on parts.
- Even on weight (both unladen weight, as stated by the source): the difference is under the 10% threshold, too small to call.
- Even on forward gears (both forward gears, as stated by the source): the difference is under the 25% threshold, too small to call.
- Not comparable on power at the PTO shaft: the 5860 (DT) TL-22 N/K (TL-22 DT/K) has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the C-360 3P has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, maximum permissible mass, a creeper range and PTO independence.
← Every figure for both machines, side by side, with sources