Landini 10.000 (DT) or VALMET 903/903-4?
Which should you choose?
On performance, no comparable figure differs by more than its threshold: on this data the machines are level. On features, the VALMET 903/903-4 is ahead on forward gears; the Landini 10.000 (DT) is ahead on PTO speeds.
- The Landini 10.000 (DT) suits PTO-driven implements (mowers, balers, pumps) better on this data: offers 1000 rpm.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | 10.000 (DT) | 903/903-4 | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 67.2 kW (90.1 hp)Traktorenlexikon, “Landini 10000” | 67.0 kW (89.8 hp)Traktorenlexikon, “Valmet 903” | EvenEven on power at the PTO shaft (both power at the PTO, claimed): the difference is under the 10% threshold for claimed figures, too small to call. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the 10.000 (DT) and the 903/903-4. |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the 10.000 (DT) and the 903/903-4. |
| Which pumps more oil for implements? | 46.5 L/min (12.3 gpm)Traktorenlexikon, “Landini 10000” | 43.0 L/min (11.4 gpm)Traktorenlexikon, “Valmet 903” | EvenEven on hydraulic flow (both pump flow, as stated by the source): the difference is under the 10% threshold, too small to call. |
| Which lifts more on the three-point hitch? | 3,060 kg (6,746 lb)Traktorenlexikon, “Landini 10000” | 2,900 kg (6,393 lb)Traktorenlexikon, “Valmet 903” | Not comparableNot comparable on three-point lift: the 10.000 (DT): lift through the full range at the hitch ends, as stated by the source (Traktorenlexikon, “Landini 10000”); the 903/903-4: lift at the hitch ends, as stated by the source (Traktorenlexikon, “Valmet 903”) — not the same quantity, basis and condition. |
| Which is heavier, for traction? | 4,525 kg (9,976 lb)Traktorenlexikon, “Landini 10000” | 3,650 kg (8,047 lb)Traktorenlexikon, “Valmet 903” | Ahead (a fact, not an advantage)The Landini 10.000 (DT) is 24% heavier (875 kg / 1,929 lb) than the VALMET 903/903-4 (both unladen weight, as stated by the source). |
| Which may carry more ballast and load? | — | — | No figureNo call on maximum permissible mass: no figure on record for the 10.000 (DT) and the 903/903-4. |
| Which has the wider choice of gears? | 12Traktorenlexikon, “Landini 10000” | 16Traktorenlexikon, “Valmet 903” | AheadThe VALMET 903/903-4 has 33% more forward gears (4 gears) than the Landini 10.000 (DT) (both forward gears, as stated by the source). |
| Which offers a creeper range? | — | — | No figureNo call on a creeper range: not stated for the 10.000 (DT) and the 903/903-4. |
| Which is faster on the road? | 30 km/h (18.6 mph)Traktorenlexikon, “Landini 10000” | 30 km/h (18.6 mph)Traktorenlexikon, “Valmet 903” | EvenEven on top speed (both top speed forward, as stated by the source): the difference is under the 10% threshold, too small to call. |
| Which offers more PTO speeds? | 540/1000 rpmTraktorenlexikon, “Landini 10000” | 540 rpmTraktorenlexikon, “Valmet 903” | AheadThe Landini 10.000 (DT) offers 1000 rpm at the PTO, which the VALMET 903/903-4 does not (as stated by the sources). |
| Which PTO runs independently of the ground drive? | independentTraktorenlexikon, “Landini 10000” | independentTraktorenlexikon, “Valmet 903” | EvenEven on PTO independence: every PTO is independent. |
| Which drives on both axles? | 2WD / 4WDTraktorenlexikon, “Landini 10000” | 2WD / 4WDTraktorenlexikon, “Valmet 903” | EvenEven on drive: every machine is available with four-wheel drive. |
| Which is newer, and what about parts? | 1978–1993 | 1979–1983 | EvenSame era: production began within 5 years of each other. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The Landini 10.000 (DT) is 24% heavier (875 kg / 1,929 lb) than the VALMET 903/903-4 (both unladen weight, as stated by the source).
- The VALMET 903/903-4 has 33% more forward gears (4 gears) than the Landini 10.000 (DT) (both forward gears, as stated by the source).
- The Landini 10.000 (DT) offers 1000 rpm at the PTO, which the VALMET 903/903-4 does not (as stated by the sources).
- Even on power at the PTO shaft (both power at the PTO, claimed): the difference is under the 10% threshold for claimed figures, too small to call.
- Even on hydraulic flow (both pump flow, as stated by the source): the difference is under the 10% threshold, too small to call.
- Even on top speed (both top speed forward, as stated by the source): the difference is under the 10% threshold, too small to call.
- Even on PTO independence: every PTO is independent.
- Even on drive: every machine is available with four-wheel drive.
- Same era: production began within 5 years of each other. We hold no parts-availability data, so there is no call on parts.
- Not comparable on three-point lift: the 10.000 (DT): lift through the full range at the hitch ends, as stated by the source (Traktorenlexikon, “Landini 10000”); the 903/903-4: lift at the hitch ends, as stated by the source (Traktorenlexikon, “Valmet 903”) — not the same quantity, basis and condition.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, maximum permissible mass and a creeper range.
← Every figure for both machines, side by side, with sources