11 material differences · fewer than 12
Tractor oneLamborghini Crono-Target 70 (DT)2005–2009No measured PTO figureTractor twoVALMET 44001993–1996No measured PTO figure
Which should you choose?
Read our verdict on the Crono-Target 70 (DT) and the 4400 → It is generated from the rows below by a fixed, versioned rule set, and names the figure behind every call.
Field by field
11 material differences · 4 fields identical or within 5%, which is not counted as material
| Field | Crono-Target 70 (DT) | 4400 | Gap |
|---|---|---|---|
| Engine | |||
| Engine power, claimed claimed | 66.1 hp | 66.1 hp | — |
| Engine declared | S.D.F. 1000.3 WT (EURO-II) | VALMET 320 DS | differs |
| Displacement declared | 3.00 L | 3.30 L | +10% 4400 |
| Maximum torque declared | 192 lb·ft · 260 N·m | 177 lb·ft · 240 N·m | +8% Crono-Target 70 (DT) |
| Transmission | |||
| Top speed declared | 18.6–24.9 mph · 30–40 km/h | 18.6 mph · 30 km/h | differs |
| Clutch declared | Pedal-operated dry Lamborghini single-plate clutch | Dry double clutch | differs |
| Hydraulics & hitch | |||
| Hydraulic control declared | Load sensing | — | — |
| Pump flow declared | — | 10.3 gpm · 39.0 L/min | — |
| Pressure declared | 3,046 psi · 210 bar | 2,901 psi · 200 bar | — |
| Three-point lift, at the coupling points declared | 6,614 lb · 3,000 kg | 6,294 lb · 2,855 kg | — |
| Rear PTO speeds declared | 540/540E rpm | 540E/540 rpm | differs |
| Weight & dimensions | |||
| Unladen weight declared | 4,564 lb · 2,070 kg | 6,151 lb · 2,790 kg | +35% 4400 |
| Wheelbase declared | 82.9 in · 2,105 mm | 83.1 in · 2,112 mm | — |
| Length declared | 128.7 in · 3,270 mm | 149.2 in · 3,790 mm | +16% 4400 |
| Width declared | 70.1–85.8 in · 1,780–2,180 mm | 80.0 in · 2,032 mm | differs |
| Ground clearance declared | 17.5 in · 445 mm | 19.9 in · 505 mm | +13% 4400 |
| Turning radius, braked declared | — | 12.8 ft · 3.90 m | — |
| Fuel tank declared | 52.8 qt · 50.0 L | 100.4 qt · 95.0 L | +90% 4400 |
Height is not in this table. It is not one measurement: the sources measure it to different points — over the cab on some machines, over the steering wheel or the exhaust on others — and the same tractor measured two ways can differ by most of a metre. It appears here only when both machines' figures carry the point they were measured to and it is the same point, which is not the case for these two. Each machine's own page prints its height as its source gives it.
Lamborghini Crono-Target 70 (DT) sources
- Source: Traktorenlexikon, “Lamborghini CRONO Target 70”
VALMET 4400 sources
- Source: Traktorenlexikon, “Valmet 4400”
- Source: Traktorenlexikon, “Valmet 465”