John Deere 5303 vs Landini R-7860 (DT) TL-20 N/M (TL-20 DT/M)
12 material differences
Which should you choose?
We will not advise between these two machines, because their power is not stated as the same quantity on both; their unladen weight differs by more than 25% (29%); they were not built in overlapping years (2003–2008; 1988–2000). The figures below are side by side so you can judge them yourself; each says whether it was measured, claimed or declared by its source.
Field by field
12 material differences · 3 fields identical or within 5%, which is not counted as material
| Field | 5303 | R-7860 (DT) TL-20 N/M (TL-20 DT/M) | Gap |
|---|---|---|---|
| Measured performance | |||
| PTO power, measured measured | 60.2 hp | — | — |
| Drawbar power, measured measured | 46.9 hp | — | — |
| Engine | |||
| Engine power, claimed claimed | — | 70.0 hp | — |
| Engine declared | John Deere 3.029 TPY-11 | Perkins LD 4.236 | differs |
| Displacement declared | 2.90 L | 3.87 L | +33% R-7860 (DT) TL-20 N/M (TL-20 DT/M) |
| Maximum torque declared | 161 lb·ft · 218.6 N·m | 195 lb·ft · 264 N·m | +21% R-7860 (DT) TL-20 N/M (TL-20 DT/M) |
| Transmission | |||
| Top speed declared | 18.6 mph · 30 km/h | 18.6 mph · 30 km/h | — |
| Clutch declared | Dry LuK double clutch with 280 mm diameter | Dry and air-cooled OMG double clutch | differs |
| Hydraulics & hitch | |||
| Hydraulic centre declared | Open centre | — | — |
| Pump flow declared | 10.8 gpm · 41.0 L/min | 9.8 gpm · 37.2 L/min | +10% 5303 |
| Pressure declared | — | 2,756 psi · 190 bar | — |
| Three-point lift at ends declared | 3,913 lb · 1,775 kg | 4,698 lb · 2,131 kg | +20% R-7860 (DT) TL-20 N/M (TL-20 DT/M) |
| Rear PTO speeds declared | 540/1000 rpm | 540/1000 rpm | — |
| Weight & dimensions | |||
| Unladen weight declared | 4,894–5,110 lb · 2,220–2,318 kg | 6,305 lb · 2,860 kg | differs |
| Wheelbase declared | 80.3 in · 2,040 mm | 89.8 in · 2,281 mm | +12% R-7860 (DT) TL-20 N/M (TL-20 DT/M) |
| Length declared | 138.4 in · 3,515 mm | 146.1 in · 3,710 mm | +6% R-7860 (DT) TL-20 N/M (TL-20 DT/M) |
| Width declared | 73.4 in · 1,865 mm | 78.3 in · 1,990 mm | +7% R-7860 (DT) TL-20 N/M (TL-20 DT/M) |
| Height declared | 96.1 in · 2,440 mm | 94.3 in · 2,395 mm | — |
| Ground clearance declared | 15.0 in · 380 mm | 20.3 in · 515 mm | +36% R-7860 (DT) TL-20 N/M (TL-20 DT/M) |
| Turning radius, braked declared | — | 13.0 ft · 3.96 m | — |
| Fuel tank declared | 72.0 qt · 68.1 L | 90.9 qt · 86.0 L | +26% R-7860 (DT) TL-20 N/M (TL-20 DT/M) |
John Deere 5303 sources
Source
- Source: OECD test report 2268, 2005
- Source: Traktorenlexikon, “John Deere 5303”
Landini R-7860 (DT) TL-20 N/M (TL-20 DT/M) sources
Source
- Source: Traktorenlexikon, “Landini 7860”
- Source: Traktorenlexikon, “Massey Ferguson MF 373”