11 material differences · fewer than 12
Tractor oneJohn Deere 2300 (A)1993–1996No measured PTO figureTractor twoVALMET 465 (465-4)1993–1997No measured PTO figure
Which should you choose?
Read our verdict on the 2300 (A) and the 465 (465-4) → It is generated from the rows below by a fixed, versioned rule set, and names the figure behind every call.
Field by field
11 material differences · 3 fields identical or within 5%, which is not counted as material
| Field | 2300 (A) | 465 (465-4) | Gap |
|---|---|---|---|
| Engine | |||
| Engine power, claimed claimed | 69.1 hp | 69.1 hp | — |
| Engine declared | ZETOR 7701 | VALMET 320 DS | differs |
| Displacement declared | 3.92 L | 3.30 L | +19% 2300 (A) |
| Maximum torque declared | 182 lb·ft · 247 N·m | 192 lb·ft · 260 N·m | +5% 465 (465-4) |
| Transmission | |||
| Top speed declared | 18.6 mph · 30 km/h | 18.6–24.9 mph · 30–40 km/h | differs |
| Clutch declared | — | dry LuK double clutch | — |
| Hydraulics & hitch | |||
| Hydraulic centre declared | — | Open centre | — |
| Pump flow declared | 10.6 gpm · 40.2 L/min | 14.5 gpm · 55.0 L/min | +37% 465 (465-4) |
| Pressure declared | 1,160 psi · 80 bar | 2,901 psi · 200 bar | +150% 465 (465-4) |
| Rear PTO speeds declared | 540/1000 rpm | 540E/540 rpm | differs |
| Weight & dimensions | |||
| Unladen weight declared | 7,187 lb · 3,260 kg | 6,217 lb · 2,820 kg | +16% 2300 (A) |
| Maximum permissible mass declared | 12,346 lb · 5,600 kg | — | — |
| Wheelbase declared | 88.8 in · 2,256 mm | 83.1 in · 2,112 mm | +7% 2300 (A) |
| Length declared | 148.6 in · 3,775 mm | 146.1 in · 3,710 mm | — |
| Width declared | 73.8–88.6 in · 1,875–2,250 mm | 79.9 in · 2,030 mm | differs |
| Ground clearance declared | 16.1 in · 410 mm | 15.9 in · 405 mm | — |
| Turning radius, braked declared | — | 11.5 ft · 3.50 m | — |
| Fuel tank declared | 100.4 qt · 95.0 L | 77.1 qt · 73.0 L | +30% 2300 (A) |
Height is not in this table. It is not one measurement: the sources measure it to different points — over the cab on some machines, over the steering wheel or the exhaust on others — and the same tractor measured two ways can differ by most of a metre. It appears here only when both machines' figures carry the point they were measured to and it is the same point, which is not the case for these two. Each machine's own page prints its height as its source gives it.
John Deere 2300 (A) sources
- Source: Traktorenlexikon, “John Deere 2300”
VALMET 465 (465-4) sources
- Source: Traktorenlexikon, “Valmet 465”