John Deere 2130 or SOMECA 750 (TD)?
Which should you choose?
The data can’t decide this. Power at the PTO shaft cannot be compared: the 2130 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 750 (TD) has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- The John Deere 2130 suits loader and hydraulic implement work better on this data: 73% (20.1 L/min / 5.3 gpm) more hydraulic flow.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | 2130 | 750 (TD) | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 55.2 kW (74.0 hp)Traktorenlexikon, “John Deere 2130” | 55.2 kW (74.0 hp)Traktorenlexikon, “Someca 750” | Not comparableNot comparable on power at the PTO shaft: the 2130 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 750 (TD) has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the 2130 and the 750 (TD). |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the 2130 and the 750 (TD). |
| Which pumps more oil for implements? | 47.6 L/min (12.6 gpm)Traktorenlexikon, “John Deere 2130” | 27.5 L/min (7.3 gpm)Traktorenlexikon, “Someca 750” | AheadThe John Deere 2130 has 73% more hydraulic flow (20.1 L/min / 5.3 gpm) than the SOMECA 750 (TD) (both pump flow, as stated by the source). |
| Which lifts more on the three-point hitch? | 2,065 kg (4,553 lb)Traktorenlexikon, “John Deere 2130” | 2,250 kg (4,960 lb)Traktorenlexikon, “Someca 750” | EvenEven on three-point lift (both lift at the hitch ends, as stated by the source): the difference is under the 10% threshold, too small to call. |
| Which is heavier, for traction? | 3,010 kg (6,636 lb)Traktorenlexikon, “John Deere 2130” | 3,045 kg (6,713 lb)Traktorenlexikon, “Someca 750” | EvenEven on weight (both unladen weight, as stated by the source): the difference is under the 10% threshold, too small to call. |
| Which may carry more ballast and load? | 4,500 kg (9,921 lb)Traktorenlexikon, “John Deere 2130” | — | No figureNo call on maximum permissible mass: no figure on record for the 750 (TD). |
| Which has the wider choice of gears? | 8 to 16Traktorenlexikon, “John Deere 2130” | 7 to 14Traktorenlexikon, “Someca 750” | EvenEven on forward gears (both forward gears, as stated by the source): the figures vary by configuration and the ranges overlap. |
| Which offers a creeper range? | — | — | No figureNo call on a creeper range: not stated for the 2130 and the 750 (TD). |
| Which is faster on the road? | 25 km/h (15.5 mph) to 30 km/h (18.6 mph)Traktorenlexikon, “John Deere 2130” | 24 km/h (14.9 mph)Traktorenlexikon, “Someca 750” | EvenEven on top speed (both top speed forward, as stated by the source): the difference is under the 10% threshold, too small to call. |
| Which offers more PTO speeds? | 540/1000 rpmTraktorenlexikon, “John Deere 2130” | 540 rpm / 1000 rpmTraktorenlexikon, “Someca 750” | EvenEven on PTO speeds: the same speeds (540, 1000 rpm). |
| Which PTO runs independently of the ground drive? | — | — | No figureNo call on PTO independence: not stated for the 2130 and the 750 (TD). |
| Which drives on both axles? | 2WD / 4WDTraktorenlexikon, “John Deere 2130” | Two-wheel or four-wheel driveTraktorenlexikon, “Someca 750” | EvenEven on drive: every machine is available with four-wheel drive. |
| Which is newer, and what about parts? | 1972–1979 | 1971–1976 | EvenSame era: production began within 5 years of each other. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The John Deere 2130 has 73% more hydraulic flow (20.1 L/min / 5.3 gpm) than the SOMECA 750 (TD) (both pump flow, as stated by the source).
- Even on three-point lift (both lift at the hitch ends, as stated by the source): the difference is under the 10% threshold, too small to call.
- Even on weight (both unladen weight, as stated by the source): the difference is under the 10% threshold, too small to call.
- Even on forward gears (both forward gears, as stated by the source): the figures vary by configuration and the ranges overlap.
- Even on top speed (both top speed forward, as stated by the source): the difference is under the 10% threshold, too small to call.
- Even on PTO speeds: the same speeds (540, 1000 rpm).
- Even on drive: every machine is available with four-wheel drive.
- Same era: production began within 5 years of each other. We hold no parts-availability data, so there is no call on parts.
- Not comparable on power at the PTO shaft: the 2130 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 750 (TD) has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, maximum permissible mass, a creeper range and PTO independence.
← Every figure for both machines, side by side, with sources