J.I. Case 1175 or J.I. Case 2096 (DT)?
Which should you choose?
On performance, every comparable figure that differs favours the J.I. Case 2096 (DT): hydraulic flow. It is also ahead on forward gears, top speed and drive.
- The J.I. Case 2096 (DT) suits loader and hydraulic implement work better on this data: 44% (26.5 L/min / 7.0 gpm) more hydraulic flow.
- The J.I. Case 2096 (DT) suits heavy draft work (ploughing, cultivating) better on this data: 16% (760 kg / 1,676 lb) heavier and four-wheel drive.
- The J.I. Case 2096 (DT) suits road haulage better on this data: 20% (5.0 km/h / 3.1 mph) more top speed.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | 1175 | 2096 (DT) | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 88.1 kW (118.2 hp)Traktorenlexikon, “Case 1175” | 86.3 kW (115.7 hp)Traktorenlexikon, “Case 2096” | EvenEven on power at the PTO shaft (both power at the PTO, claimed): the difference is under the 10% threshold for claimed figures, too small to call. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the 1175 and the 2096 (DT). |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the 1175 and the 2096 (DT). |
| Which pumps more oil for implements? | 60.6 L/min (16.0 gpm)Traktorenlexikon, “Case 1175” | 87.1 L/min (23.0 gpm)Traktorenlexikon, “Case 2096” | AheadThe J.I. Case 2096 (DT) has 44% more hydraulic flow (26.5 L/min / 7.0 gpm) than the J.I. Case 1175 (both pump flow, as stated by the source). |
| Which lifts more on the three-point hitch? | — | 3,742 kg (8,250 lb)Traktorenlexikon, “Case 2096” | No figureNo call on three-point lift: no figure on record for the 1175. |
| Which is heavier, for traction? | 4,626 kg (10,199 lb)Traktorenlexikon, “Case 1175” | 5,386 kg (11,874 lb)Traktorenlexikon, “Case 2096” | Ahead (a fact, not an advantage)The J.I. Case 2096 (DT) is 16% heavier (760 kg / 1,676 lb) than the J.I. Case 1175 (both unladen weight, as stated by the source). |
| Which may carry more ballast and load? | — | — | No figureNo call on maximum permissible mass: no figure on record for the 1175 and the 2096 (DT). |
| Which has the wider choice of gears? | 8Traktorenlexikon, “Case 1175” | 12Traktorenlexikon, “Case 2096” | AheadThe J.I. Case 2096 (DT) has 50% more forward gears (4 gears) than the J.I. Case 1175 (both forward gears, as stated by the source). |
| Which offers a creeper range? | — | — | No figureNo call on a creeper range: not stated for the 1175 and the 2096 (DT). |
| Which is faster on the road? | 25 km/h (15.5 mph)Traktorenlexikon, “Case 1175” | 30 km/h (18.6 mph)Traktorenlexikon, “Case 2096” | AheadThe J.I. Case 2096 (DT) has 20% more top speed (5.0 km/h / 3.1 mph) than the J.I. Case 1175 (both top speed forward, as stated by the source). |
| Which offers more PTO speeds? | 540/1000 rpmTraktorenlexikon, “Case 1175” | 540/1000 rpmTraktorenlexikon, “Case 2096” | EvenEven on PTO speeds: the same speeds (540, 1000 rpm). |
| Which PTO runs independently of the ground drive? | independentTraktorenlexikon, “Case 1175” | independentTraktorenlexikon, “Case 2096” | EvenEven on PTO independence: every PTO is independent. |
| Which drives on both axles? | 2WDTraktorenlexikon, “Case 1175” | Two-wheel or four-wheel driveTraktorenlexikon, “Case 2096” | AheadThe J.I. Case 2096 (DT) is available with four-wheel drive; the J.I. Case 1175 is two-wheel drive (as stated by the sources). |
| Which is newer, and what about parts? | 1972–1978 | 1984–1985 | Ahead (a fact, not an advantage)The J.I. Case 2096 (DT) is newer: production began 12 years later. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The J.I. Case 2096 (DT) has 44% more hydraulic flow (26.5 L/min / 7.0 gpm) than the J.I. Case 1175 (both pump flow, as stated by the source).
- The J.I. Case 2096 (DT) is 16% heavier (760 kg / 1,676 lb) than the J.I. Case 1175 (both unladen weight, as stated by the source).
- The J.I. Case 2096 (DT) has 50% more forward gears (4 gears) than the J.I. Case 1175 (both forward gears, as stated by the source).
- The J.I. Case 2096 (DT) has 20% more top speed (5.0 km/h / 3.1 mph) than the J.I. Case 1175 (both top speed forward, as stated by the source).
- The J.I. Case 2096 (DT) is available with four-wheel drive; the J.I. Case 1175 is two-wheel drive (as stated by the sources).
- The J.I. Case 2096 (DT) is newer: production began 12 years later. We hold no parts-availability data, so there is no call on parts.
- Even on power at the PTO shaft (both power at the PTO, claimed): the difference is under the 10% threshold for claimed figures, too small to call.
- Even on PTO speeds: the same speeds (540, 1000 rpm).
- Even on PTO independence: every PTO is independent.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, three-point lift, maximum permissible mass and a creeper range.
← Every figure for both machines, side by side, with sources