10 material differences · fewer than 12
Tractor oneInternational Harvester 7661971–1973No measured PTO figureTractor twoLandini 8830 (DT) TL-23 N/E (TL-23 DT/F)1983–1987No measured PTO figure
Which should you choose?
Read our verdict on the 766 and the 8830 (DT) TL-23 N/E (TL-23 DT/F) → It is generated from the rows below by a fixed, versioned rule set, and names the figure behind every call.
Field by field
10 material differences · 3 fields identical or within 5%, which is not counted as material
| Field | 766 | 8830 (DT) TL-23 N/E (TL-23 DT/F) | Gap |
|---|---|---|---|
| Engine | |||
| Engine power, claimed claimed | 78.9 hp | 78.9 hp | — |
| Engine declared | INTERNATIONAL HARVESTER C-291 | Perkins A 4.248 | differs |
| Displacement declared | — | 4.07 L | — |
| Maximum torque declared | — | 208 lb·ft · 282 N·m | — |
| Transmission | |||
| Top speed declared | 18.6 mph · 30 km/h | 18.6 mph · 30 km/h | — |
| Clutch declared | Pedal-operated DYNA-LIFE clutch | Dry and air-cooled OMG double clutch | differs |
| Hydraulics & hitch | |||
| Pump flow declared | 12.0 gpm · 45.5 L/min | 9.3 gpm · 35.3 L/min | +29% 766 |
| Rear PTO speeds declared | 540/1000 rpm | 540/1000 rpm | — |
| Weight & dimensions | |||
| Unladen weight declared | 11,341 lb · 5,144 kg | 6,217 lb · 2,820 kg | +82% 766 |
| Wheelbase declared | 104.8 in · 2,662 mm | 90.6 in · 2,300 mm | +16% 766 |
| Length declared | 165.0 in · 4,191 mm | 151.6 in · 3,850 mm | +9% 766 |
| Width declared | 98.0 in · 2,489 mm | 76.8 in · 1,950 mm | +28% 766 |
| Ground clearance declared | 14.0 in · 356 mm | 22.0 in · 560 mm | +57% 8830 (DT) TL-23 N/E (TL-23 DT/F) |
| Turning radius, braked declared | 11.2 ft · 3.40 m | 13.0 ft · 3.95 m | +16% 8830 (DT) TL-23 N/E (TL-23 DT/F) |
| Fuel tank declared | 147.9 qt · 140.0 L | 63.9 qt · 60.5 L | +131% 766 |
Height is not in this table. It is not one measurement: the sources measure it to different points — over the cab on some machines, over the steering wheel or the exhaust on others — and the same tractor measured two ways can differ by most of a metre. It appears here only when both machines' figures carry the point they were measured to and it is the same point, which is not the case for these two. Each machine's own page prints its height as its source gives it.
International Harvester 766 sources
- Source: Traktorenlexikon, “IHC 766”
- Source: Traktorenlexikon, “Farmall Farmall 756”
Landini 8830 (DT) TL-23 N/E (TL-23 DT/F) sources
- Source: Traktorenlexikon, “Landini 8830 (DT)”
- Source: Traktorenlexikon, “Massey Ferguson MF 178”