International Harvester 1055 XL or Landini 10.000 (DT)?
Which should you choose?
The data can’t decide this. Power at the PTO shaft cannot be compared: the 1055 XL has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 10.000 (DT) has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- The Landini 10.000 (DT) suits loader and hydraulic implement work better on this data: 29% (10.5 L/min / 2.8 gpm) more hydraulic flow.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | 1055 XL | 10.000 (DT) | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 73.5 kW (98.6 hp)Traktorenlexikon, “IHC 1055 XL” | 73.5 kW (98.6 hp)Traktorenlexikon, “Landini 10000” | Not comparableNot comparable on power at the PTO shaft: the 1055 XL has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 10.000 (DT) has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the 1055 XL and the 10.000 (DT). |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the 1055 XL and the 10.000 (DT). |
| Which pumps more oil for implements? | 36.0 L/min (9.5 gpm)Traktorenlexikon, “IHC 1055 XL” | 46.5 L/min (12.3 gpm)Traktorenlexikon, “Landini 10000” | AheadThe Landini 10.000 (DT) has 29% more hydraulic flow (10.5 L/min / 2.8 gpm) than the International Harvester 1055 XL (both pump flow, as stated by the source). |
| Which lifts more on the three-point hitch? | 4,324 kg (9,532 lb)Traktorenlexikon, “IHC 1055 XL” | 3,060 kg (6,746 lb)Traktorenlexikon, “Landini 10000” | Not comparableNot comparable on three-point lift: the 1055 XL: lift at an unstated point, as stated by the source (Traktorenlexikon, “IHC 1055 XL”); the 10.000 (DT): lift through the full range at the hitch ends, as stated by the source (Traktorenlexikon, “Landini 10000”) — not the same quantity, basis and condition. |
| Which is heavier, for traction? | 4,370 kg (9,634 lb)Traktorenlexikon, “IHC 1055 XL” | 4,525 kg (9,976 lb)Traktorenlexikon, “Landini 10000” | EvenEven on weight (both unladen weight, as stated by the source): the difference is under the 10% threshold, too small to call. |
| Which may carry more ballast and load? | — | — | No figureNo call on maximum permissible mass: no figure on record for the 1055 XL and the 10.000 (DT). |
| Which has the wider choice of gears? | 16Traktorenlexikon, “IHC 1055 XL” | 12Traktorenlexikon, “Landini 10000” | AheadThe International Harvester 1055 XL has 33% more forward gears (4 gears) than the Landini 10.000 (DT) (both forward gears, as stated by the source). |
| Which offers a creeper range? | — | — | No figureNo call on a creeper range: not stated for the 1055 XL and the 10.000 (DT). |
| Which is faster on the road? | 25 km/h (15.5 mph) to 30 km/h (18.6 mph)Traktorenlexikon, “IHC 1055 XL” | 30 km/h (18.6 mph)Traktorenlexikon, “Landini 10000” | EvenEven on top speed (both top speed forward, as stated by the source): the figures vary by configuration and the ranges overlap. |
| Which offers more PTO speeds? | 540/1000 rpmTraktorenlexikon, “IHC 1055 XL” | 540/1000 rpmTraktorenlexikon, “Landini 10000” | EvenEven on PTO speeds: the same speeds (540, 1000 rpm). |
| Which PTO runs independently of the ground drive? | independentTraktorenlexikon, “IHC 1055 XL” | independentTraktorenlexikon, “Landini 10000” | EvenEven on PTO independence: every PTO is independent. |
| Which drives on both axles? | Two-wheel or four-wheel driveTraktorenlexikon, “IHC 1055 XL” | Two-wheel or four-wheel driveTraktorenlexikon, “Landini 10000” | EvenEven on drive: every machine is available with four-wheel drive. |
| Which is newer, and what about parts? | 1981–1982 | 1978–1993 | EvenSame era: production began within 5 years of each other. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The Landini 10.000 (DT) has 29% more hydraulic flow (10.5 L/min / 2.8 gpm) than the International Harvester 1055 XL (both pump flow, as stated by the source).
- The International Harvester 1055 XL has 33% more forward gears (4 gears) than the Landini 10.000 (DT) (both forward gears, as stated by the source).
- Even on weight (both unladen weight, as stated by the source): the difference is under the 10% threshold, too small to call.
- Even on top speed (both top speed forward, as stated by the source): the figures vary by configuration and the ranges overlap.
- Even on PTO speeds: the same speeds (540, 1000 rpm).
- Even on PTO independence: every PTO is independent.
- Even on drive: every machine is available with four-wheel drive.
- Same era: production began within 5 years of each other. We hold no parts-availability data, so there is no call on parts.
- Not comparable on power at the PTO shaft: the 1055 XL has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 10.000 (DT) has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- Not comparable on three-point lift: the 1055 XL: lift at an unstated point, as stated by the source (Traktorenlexikon, “IHC 1055 XL”); the 10.000 (DT): lift through the full range at the hitch ends, as stated by the source (Traktorenlexikon, “Landini 10000”) — not the same quantity, basis and condition.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, maximum permissible mass and a creeper range.
← Every figure for both machines, side by side, with sources